Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Service Centre in order to
avoid a hazard.
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/tool/battery must be placed in a well ventilated
$
u
area when charging.
+
The charger is intended for indoor use only.
Read the instruction manual before use.
Electrical safety
i
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER service
centre in order to avoid a hazard
Features
This tool includes some or all of the following features.
1. On/Off switch
2. Forward/reverse selector
3. Drilling mode selector
4. Depth stop
5. Tool holder
6. Side handle
7. Led work light
8. Battery
Assembly
@
Use
WARNING! Let the tool work at its own pace. Do not
overload.
Charge battery fully before first use.
u
Note: If unit cuts off suddenly in use, remove battery pack and
place on charge to fully charge.
Note: If unit will not restart after heavy use, allow tool and
battery pack to cool down before resuming work.
Charging the battery (fig. A, B)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
8
(Original instructions)
@
WARNING! Do not charge the battery at ambient
temperatures below 10 °C or above 40 °C.
Recommended charging temperature: approx. 24 °C.
NOTE: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger will
begin to charge automatically when the cell temperature
warms up or cools down.
To charge the battery, insert the Battery (8) into the desk
u
charger (9) or the cup charger (11) depending on your
model. The battery will only fit into the charger one way.
Plug the desk charger (9) or the cup charger (11) into a
u
suitable power source and switch on.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Fitting and removing the battery (fig. C, D)
To fit the battery, line it up with the receptacle on the tool.
u
Slide the battery into the receptacle and push until the
battery snaps into place.
To remove the battery, push the release button (8a) and
u
remove the battery from the receptacle.
Fitting the side handle and depth stop (fig. E)
Turn the grip clockwise until you can slide the side handle
u
(6) onto the front of the tool as shown.
Rotate the side handle into the desired position.
u
Insert the depth stop (4) into the mounting hole as shown.
u
Set the depth stop to the desired position. The maximum
u
drilling depth is equal to the distance between the tip of
the drill bit and the front end of the depth stop.
Ensure handle detents (23) are locked onto the ribs on the
u
housing (22).
Tighten the side handle by turning the grip counterclockwise.
u
Fitting an accessory (fig. F - G)
Clean and grease the shank (12) of the accessory.
u
Insert the shank into the tool holder (5).
u
Push the accessory down and turn it slightly until it fits into
u
the slots.
Pull on the accessory to check if it is properly locked.
u
The hammering function requires the accessory to be able
to move axially several centimetres when locked in the
tool holder.
To remove the accessory, pull back the sleeve (13) and
u
pull out the accessory.
Keyed chuck (fig. H)
Open the chuck by turning the sleeve (14) anti-clockwise.
u
Insert the bit shaft (16) into the chuck.
u
Insert the chuck key (17) into the hole (15) in the side of
u
the chuck and turn clockwise until tight.
Publicidad
