Before Starting The Equipment; Continuous Operation - EINHELL TC-ID 18 Li Manual De Instrucciones

5. Before starting the equipment

5.1. Fitting the additional handle
(Fig. 2-3/Item 7)
The additional handle (7) enables you to achieve
better stability whilst using the hammer drill. Do
not use the tool without the additional handle.
The additional handle (7) is secured to the
hammer drill by a clamp. Turning the handle
clockwise tightens this clamp. Turning it anti-
clockwise will release the clamp.
•
The supplied additional handle (7) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (7), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (7) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop (Fig.
4/Item 2)
The depth stop (2) is held in place by the
additional handle (7) by clamping. The clamp can
be released and tightened by turning the handle.
•
Release the clamp and fit the depth stop (2)
in the recess provided for it in the additional
handle.
•
Set the depth stop (2) to the same level as
the drill bit.
•
Pull the depth stop back by the required
drilling depth.
•
Turn the handle on the additional handle (7)
until it is secure.
•
Now drill the hole until the depth stop (2)
touches the workpiece.
5.3 Fitting the drill bit (Fig. 5)
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
This hammer drill is fitted with a keyless
chuck (1).
•
Open the chuck (1). The drill bit opening must
be large enough to fit the drill bit into.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Close the chuck (1). Check that the drill bit is
secure in the chuck (1).
Anl_TC_ID_18_Li_SPK7_USA.indb 11 Anl_TC_ID_18_Li_SPK7_USA.indb 11
EN
6. Operation
6.1 On/Off switch (Fig. 7/Item 5)
Infi nitely variable speed control is possible with
the On/Off switch (5). The further you push the
switch, the higher the speed of the cordless
hammer drill.
To switch on:
Press the On/Off switch (5)

Continuous operation:

Secure the On/Off switch (5) with the locking
button (4).
To switch off :
Press the On/Off switch (5) briefl y.
6.2 Changeover switch (Fig. 7/Item 6)
Using the changeover switch (6) above the On/Off
switch (5) you can select the direction of rotation
of the cordless hammer drill and lock the cordless
hammer drill so that it cannot be switched on
accidentally. You can select between clockwise
and counter-clockwise rotation. To avoid causing
damage to the gearing, the direction of rotation
must only be changed when the equipment is at
a standstill. When the slide switch is in the middle
position, the On/Off switch is blocked.
6.3 Drill / hammer drill selector switch
(Fig. 8/Item 3)
Change switch position only when the drill is at a
standstill!
Drill
Drill / hammer drill selector switch (3) in the drill
position. (Position A)
Use for: Wood, metal, plastic
Hammer drill
Drill / hammer drill selector switch (3) in the
hammer drill position. (Position B)
Use for: Concrete, rock, masonry
Tips for working with your hammer drill
6.4 Drilling concrete and masonry
•
Switch the Drill/Hammer drill selector switch
(3) to position B (Hammer drill).
•
Always use carbide drill bits and a high speed
setting for drilling into masonry and concrete.
- 11 -
22.04.2022 11:04:18 22.04.2022 11:04:18