Publicidad
Idiomas disponibles
Idiomas disponibles
FUNCTIONAL DESCRIPTION
2
1
10
9
1. Laser aperture
2. Mode button
3. Fuel gauge
4. Power save indicator
5. On/Off dial
6. Pivot Bracket
SPECIFICATIONS
Cat. No. ..................................................... 3624-20
Volts.............................................................. 12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
Laser............................................................Class 2
Lines Max Power ................................. P
Points Max Power................................ P
Pulse Frequency..........................................10 KHz
Pulse Duration Normal Mode ................. T
Pulse Duration Power Save.................... T
Wavelength.......................................... 510-530 nm
Lines Beam Divergence ................................. 1 rad
Points Beam Divergence .......................... 0.5 mrad
Storage Temp .................................... -4°F to 120°F
Working Range .................................................125'
Range with Detector .........................................165'
Accuracy ...............................................±1/8" @ 33'
Settle Time ......................................... < 3 Seconds
Tripod Mount ..................................1/4"-20, 5/8"-11
Ingress Protection............................................ IP54
Drop Rating .......................................................1 m
Leveling ............Auto ±°4 side to side, front to back
Recommended Ambient
Operating Temperature ................... -4°F to 104°F
3
4
5
6
7
8
7. Micro adjust
8. Threaded tripod
attachment
9. Magnets
10. Nail/Screw hole
≤ 7 mW
AVG
≤ 1 mW
AVG
≤ 80 µs
P
≤ 50 µs
P
SYMBOLOGY
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove the battery pack
WARNING
anytime the tool is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Power Save
Use power save mode to extend the battery run time.
Power save mode is indicated by dimmed laser beams
and the Power Save Indicator pulsing. Visual range is
decreased in power save mode. Power Save Indicator
will change from pulsing to solid Green when turned
OFF. The tool will automatically switch to power save
mode if less than 7% of battery charge remains.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. When less than 7% of charge is
left, 1 light on the fuel gauge will flash continuously.
To signal the end of charge, will flash 4 times and
then the tool will shut off. Charge the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash. Allow the battery to cool down.
To reduce the risk of injury or dam-
WARNING
age, securely mount/attach the
laser before starting an operation. Injury/damage
may occur if the laser falls.
Mounting/Adjusting the Laser Level
The pivot bracket can be used to mount the laser
level in multiple ways:
• Use the embedded magnets to secure the laser level
to steel studs, steel beams, etc.
• Use the keyhole slot to hang the laser level on the
wall with a nail or screw.
• Set the laser level on a flat surface.
• Position the laser and/or wall mount on a stable
surface.
• Use the 1/4"-20 or 5/8"-11 threaded insert to mount
on a tripod.
• Once the level is mounted, use the micro adjustment
knobs to fine tune the laser line.
3
Volts
Direct Current
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Magnets
Read operator's manual
Publicidad
