Hikmicro B Serie Guia De Inicio Rapido página 6

including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est
autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.equipment complies with IC
RSS-102 radiation exposure limits set forth for an
uncontrolled environment.
ce matériel est conforme aux limites de dose
d'exposition aux rayonnements, CNR-102 énoncée
dans un autre environnement.
Safety Instruction
These instructions are intended to ensure that user
can use the product correctly to avoid danger or
property loss.
Laws and Regulations
● Use of the product must be in strict compliance
with the local electrical safety regulations.
Transportation
● Keep the device in original or similar packaging
while transporting it.
● Keep all wrappers after unpacking them for
future use. In case of any failure occurred, you
need to return the device to the factory with the
original wrapper. Transportation without the
original wrapper may result in damage on the
device and the company shall not take any
responsibilities.
● Do not drop the product or subject it to physical
shock. Keep the device away from magnetic
interference.
Power Supply
● The input voltage should meet the Limited Power
Source (3.7 VDC, 0.5 A) according to the
IEC61010-1 standard. Please refer to technical
specifications for detailed information.
● Make sure the plug is properly connected to the
power socket.
● DO NOT connect multiple devices to one power
adapter, to avoid over-heating or fire hazards
caused by overload.
● Use the power adapter provided by a qualified
manufacturer. Refer to the product specification
for detailed power requirements.
Battery
● The built-in battery cannot be dismantled. Please
contact the manufacture for repair if necessary.
The battery may explode if it is replaced by an
incorrect type. Replace with the same or
equivalent type only. Dispose of used batteries in
conformance with the instructions provided by
the battery manufacturer.
● Use the battery provided by a qualified
manufacturer. Refer to the product specification
for detailed battery requirements.
● For long-term storage of the battery, make sure
it is fully charged every half year to ensure the
battery quality. Otherwise, damage may occur.
● Make sure the plug is properly connected to the
power socket.
● When the device is powered off and the RTC
battery is full, the time settings can be kept for
4 months.
● Before the first use, charge the lithium battery
for more than 8 hours.
Maintenance
● If the product does not work properly, please
contact your dealer or the nearest service center.
We shall not assume any responsibility for
problems caused by unauthorized repair or
maintenance.
● Wipe the device gently with a clean cloth and a
small quantity of ethanol, if necessary.
● If the equipment is used in a manner not
specified by the manufacturer, the protection
provided by the device may be impaired.
● Your camera will periodically perform a
self-calibration to optimize image quality and
measurement accuracy. In this process the image
will pause briefly and you will hear a "click" as a
shutter moves in front of the detector. The
self-calibration will be more frequent during the
startup or in very cold or hot environments. This
is a normal part of operation to ensure optimum
performance for your camera.
Calibration Service
● We recommend you send the device back for
calibration once a year, and please contact the
local dealer for the information on maintenance
points. For more detailed calibration services,
please visit HIKMICRO official website.
Using Environment
● Make sure the running environment meets the
requirement of the device. The operating
temperature shall be -10°C to 50°C (14°F to
122°F), humidity shall be 90% or less, and height
≤ 5000 m.
● Place the device in a dry and well-ventilated
environment.
● DO NOT expose the device to high
electromagnetic radiation or dusty
environments.
● DO NOT aim the lens at the sun or any other
bright light.
● When any laser equipment is in use, make sure
that the device lens is not exposed to the laser
beam, or it may burn out.
Technical support
● https://www.hikmicrotech.com portal will help
you as a HIKMICRO customer to get the most out
of your HIKMICRO products. The portal gives you
access to our support team, software and
documentation, service contacts, etc.
Emergency
● If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the
power cable, and contact the service center.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road,
Xixing Subdistrict,Binjiang District, Hangzhou,
Zhejiang 310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products
4