Operating Environment - Sharp UD-P16E-W Manual Del Usuario

5

Operating environment

• Working temperature: 5 °C to 35 °C.
• This machine is suitable for indoors, e.g. Living room, study, office room,
warehouse, basement, underground garage.
• Make sure the door and window are closed before turning on the unit to
get the best result.
• Ensure that the unit is placed on a stable and flat floor surface. If the
floor's surface is not even, there is a risk that the unit may be unstable
and topple over. Also excessive vibration and noise may be result.
Components diagrams – parts names
Refer to the 2 and 3 on page 1 for the location of the following parts:
1. Top casing
2. Handle
3. Control panel
4. Front cover
5. Louver (air outlet)
6. Mains lead and plug
7. Castor
8. Water tank
9. Drain pipe (not supplied)
10. Air intake and dust filter
Operating Introduction – How to operate
Control panel
Refer to the 4 of the control panel on page 1.
The name and function of control panel
1. POWER – Press this button to switch the power on and off.
2. MODE – Press this button to set the dry clothes mode or dehumidify
mode
3. HUMIDITY – Press this button to set the desired humidity.
4. TIMER/LOCK – Press this button to set the machine shutdown time.
The display will show the shutdown time accordingly. Press this button
for 3 seconds, could turn on or off the child lock function, the lock icon
will show or off on the display.
5. SPEED – Press this button to adjust the fan speed (there are 2 fan
speeds).
6. SWING – Press this button to turn on or off the swing function.
7. ON/OFF INDICATOR – Lights up when the unit is on, turns off when
unit is off.
8. DRY INDICATOR – Turns on during the drying function.
9. DEHYMIDIIFNG INDICATOR – Turns on when the unit is dehumidifying.
10. DEFROST INDICATOR – Lights up when the unit is in the defrost
mode.
11. DISPLAY – Shows the current status of the dehumidifying function
(humidity in the air) and other functions.
12. TANK FULL – Lights up when the water tank is full.
13. KEY LOCK INDICATOR – When the key lock is active, this indicator
lights up.
14. TIMER ON INDICATOR – When the timer is active, this indicator lights
up.
15. FAN SPEED INDICATOR – When the speed of the fan is high or low the
respective light illuminates.
16. LOUVER ON INDICATOR – When the louver is in operation, this indica-
tor turns on.
Operating introduction
Power on
Plug in the appliance to the mains supply and press the POWER button, it
will start and the air outlet louver will open.
When powered on, the unit will start to dehumidify with the fan set to
high. The compressor will activate after three minutes.
If the appliance is turned off via the POWER switch and not unplugged
from the mains supply, it will start up again in the same mode.
Power off
While the appliance is operating, press the POWER button to turn it off.
Mode setting button
You can change the mode of the dehumidifier to dry clothes or
dehumidify. To do this press the MODE button.
1. Dry Clothes Function: When the DRY indicator is illuminated the unit
will continually dehumidify whatever the ambient humidity is. The fan
speed will be locked in the DRY function and can not be changed.
2. Dehumidify Function: When the DEHUMIDIFY indicator is illuminated
the unit will dehumidify the air. While in this mode, the fan speed can
be set and the humidity setting can be controlled.
Humidity setting
To change the humidity level, press the humidity setting button, each time
the button is pressed, the display will change as follows CO~40%~45%~50
%~55%~60%~65%~70%~CO. After setting the humidity level, the display
will revert to the current moisture level detected by the internal sensor.
When the machine detects that the ambient humidity is 2 % lower
than the set humidity, the machine will stop dehumidifying, the fan
will keep working in low speed. When the machine detects that the
ambient humidity is 2 % higher than the set humidity, the machine will
start dehumidifying and the fan come back to work at set speed. When
the ambient humidity is ≤30 %, the LO icon will be displayed; When the
ambient humidity is ≥80 %, the HI icon will be displayed.
CO means Continuously dehumidify whatever the ambient humidity is.
The machine default setting is CO when switch on the machine in the
beginning.
When operating in the dry clothes function, the machine is running
in CO status.
Timer
To start the timer function, press the TIMER button; the timer indicator will
illuminate. On each press of the TIMER button, the display will change from
1 to 8 hours in 1 hour steps. 0H means that the timer mode is canceled.
While in the timer mode, if the water tank is full or if it enters the auto
defrost mode, the unit will stop.
Fan Speed setting
To control the speed of the fan, press the FAN button. There are two fan
speeds which are low or high; each time the FAN button is pressed, the
speed of the fan toggles between these two speeds. Note that the fan
speed can not be set while in the DRY function.
Swing
To make the air outlet louver open and close continually, press the SWING
button. Pressing the SWING button again disables this function.
Lock function
To prevent accidental operaiton of the unit, the keypad can be locked.