Publicidad
Idiomas disponibles
Idiomas disponibles
W I R E − F R E E S H A D I N G S Y S T E M
3
INSTALL FOOT COVERS
IMPORTANT: Before proceeding, confirm all
brackets are located properly and securely
mounted, ensuring that the installed shade(s)
will be level and unobstructed. Make any final
bracket position adjustments needed before
installing bracket foot covers.
Position a cover on the mounting surface as shown,
and slide it over the bracket foot to conceal the
fastener heads. Repeat for the remaining brackets.
wall mount - right operator bracket shown
5
HANG THE SHADE IN THE BRACKETS:
A. Insert the Idler
1. Insert the shade idler into the idler bracket socket as shown. The idler will
land with an audible "CLICK" when it is fully seated. Wall mount shown.
2. Pull back on the shade gently to verify there is resistance, confirming the
idler is engaged in the bracket.
6
INSTALL BATTERIES:
A. Open the Battery Door
1. To access the Battery Door, grasp the fabric roll at
the drive end and pull it out, away from the bracket.
Battery Door
B. Load the Batteries*
1. Use a finger to reach into the battery opening and pull
out the Battery Sleeve. Pull the sleeve all the way out
and away from the shade.
7
FINAL SHADE SETUP:
A. Power the Shade
• Swing the Battery Door up into the battery opening. Push it
in and then down to secure it back in its original position.
• The shade LED will flash a multi-color sequence when
battery contact is made, confirming the shade is powered.
11/2021
P/N 045893 Rev. A
4
INSTALL THE SLIDE RING ON THE SHADE:
IMPORTANT: Before attaching
the Slide Ring to the shade,
Battery
refer to the pictures at right for
correct Slide Ring orientation
according to the bracket
type and operator side.
Note the position of the
Retention Clip
Ribbon
(always on top,
Cable
always opposite
the Ribbon Cable)
Shade Orientation - Operator End
! CAUTION: RISK OF FALLING OBJECTS. Read and follow all instructions for securing the Slide Ring to the shade using the Retention Clip. Failure to follow these instructions could result in minor to moderate injury.
A. Convert to Left Operator, if applicable
IMPORTANT: Wall and jamb brackets are operator-side reversible, and factory-
configured for RIGHT OPERATOR shades. When installing a LEFT OPERATOR
shade with wall or jamb brackets, you must reverse the Retention Clip position as
shown below.
When installing a RIGHT OPERATOR shade, or when the operator bracket is
ceiling-mounted, SKIP THIS STEP and proceed directly to Step B.
Retention Clip
(default position
for right operator)
1. From the backside of the Slide Ring,
2. Install only one (1) screw, and do not
remove the two (2) Retention Clip
tighten it completely.
screws and move the Retention Clip
3. Keep the second screw nearby, and
to the opposite side of the Slide Ring.
proceed directly to step 4B.2.
! CAUTION: RISK OF FALLING OBJECTS. Read and follow all instructions for hanging the shade. Failure to follow these instructions could result in minor to moderate injury.
B. Engage the Operator End
Align the channels on the backside of the Slide Ring with the with the tracks on the operator bracket, and slide the shade into the bracket. Continue sliding the shade all the way back
into the bracket as far as it will go until it seats with an audible "CLICK". Remove any packaging material that is still on the fabric roll.
Wall / Jamb
2. Push in, then up on the Battery Door to release it from
the shade.
3
2
1
IMPORTANT: DO NOT pull the Battery Door away from the shade. The Battery Door is attached to the shade by the
Ribbon Cable. Allow the door to hang below the battery opening as shown, and do not allow the Ribbon Cable to twist.
2. Load the Battery Sleeve with NEW 1.5 V Alkaline,
D-Cell batteries. Information on the sleeve indicates
quantity and direction.
B. Assign a Pico Control*
Shade
Button
• Tap the shade button. The shade LED will light steady GREEN.
• Press and hold the Close button on the Pico for 10 seconds.
The shade button LED and the Pico LED will both flash rapidly,
then turn off, confirming the assignment.
* To assign control of the shade within a system, refer to the
setup guide supplied with the system.
Wall or Jamb - Right Operator
Wall or Jamb - Left Operator
Door
Retention Clip
Retention Clip
Ribbon Cable
Ribbon Cable
B. Attach the Slide Ring to the Shade
1. From the backside of the Slide Ring,
loosen the two (2) Retention Clip screws.
Leave one screw loosened, and remove
the other completely.
Battery
Door
Retention Clip
(repositioned
for left operator)
2. Orient the operator end of the
shade as shown.
Ceiling
3. The open Battery Door allows access to the Battery Sleeve.
Battery Sleeve
Ribbon Cable
3. Slide the loaded Battery Sleeve back into the shade as
far as it will go.
C. Set the Open Limit
• Tap the shade button. The LED will light steady GREEN.
• Press and hold the Open and Raise buttons on the Pico remote control for 10 seconds.
• The LED will flash rapidly, then turn steady GREEN.
• Use the Raise / Lower to move the shade to the desired open limit, then press and hold
the Open button for 10 seconds. The shade button LED and the Pico LED will both flash
rapidly, then turn off, confirming the open limit is set.
Roller Shade Chassis Installation & Setup Guide
Ceiling / Door Mount - Right Operator
Retention Clip
Ribbon Cable
Retention Clip
Grooves (4)
Ribbon
wall mount - right operator Slide Ring shown
Cable
3. Align the (4) ribs on the Slide Ring
with the grooves on the shade and
snap the Slide Ring onto the shade.
Door
*
Important Battery Information
BATTERIES: Install NEW 1.5 V Alkaline, D-Cell batteries. Do not mix brands or types. Lutron
recommends Duracell
or RAYOVAC
batteries. The Battery Sleeve indicates correct orientation.
®
®
BATTERY LIFE: Battery life varies with shade size, fabric weight, and daily usage patterns. Estimated
battery life will be calculated in the shade ordering tool based on size and fabric selections.
FLEXIBLE BATTERY SLEEVE: If an adjacent object or structure obstructs full removal of the Battery
Sleeve, but is at least 3 in (76 mm) away from the Battery Door, the Battery Sleeve may be cut at the
locations shown to add flexibility and allow removal and installation of batteries one-by-one.
CUT HERE
CUT HERE
CUT HERE
CLOSE-QUARTERS INSTALLATIONS: If the shade was mounted in a location or at an inside-mount
depth that allows less than 3 in (76 mm) of clearance for Battery Sleeve removal, the shade must be
removed from the brackets to install or change batteries.
TO REMOVE THE SHADE FROM THE BRACKETS:
Extend the operator bracket Slide Ring, then press the
Slide Ring release (behind the shade) to release the
shade. Pull the idler end of the shade out of the idler
bracket socket.
D. Set the Close Limit
• Tap the shade button. The LED will light steady GREEN.
• Press and hold the Open and Raise buttons on the Pico remote control for 10 seconds.
• The LED will flash rapidly, then turn steady GREEN.
• Use the Raise / Lower buttons to move the shade to the desired close limit, then press
and hold the Close button for 10 seconds. The shade button LED and the Pico LED will
both flash rapidly, then turn off, confirming the close limit is set.
• Slide the shade fully back into the bracket as shown in Step 5B.
The Lutron logo and Palladiom are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries
Duracell is a registered trademark of Duracell U.S. Operations, Inc., RAYOVAC is a registered trademark of Spectrum Brands, Inc.
Ceiling / Door Mount - Left Operator
Retention Clip
Ribbon Cable
wall mount - right operator Slide Ring shown
4. Swing the Retention Clip back into its
original position and reinstall the second
screw. Tighten both screws firmly.
Slide Ring
Release
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299, U.S.A.
Publicidad
