Symbols; Functional Description; Operating Instruction; Cleaning And Maintenence - MaxPro PROFESSIONAL MPBS900/533V Manual De Instrucciones

• Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in c
with a ves for wood c wear a dust mask and work with a dust extr
connectable
• Follow the dust-related na requirements for the materials you want to work with
• Wear prot ve gloves, safety glasses, close-fi
• Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than
by hand)
• When sanding metal, sparks are generated; do not use dustbox and keep other persons and combus
material from work area
DURING USE
• Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool
• Do not touch the moving sanding disc
• In case of electrical or mechanic
• If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect
the plug
AFTER USE
• When you put away the tool, switch off the motor and ensure that all moving parts have come to a
complete stands CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not le
una ended

SYMBOLS

Read the manual
Warning

FUNCTIONAL DESCRIPTION

4.Belt tracking knob 5.Tension lever

OPERATING INSTRUCTION

SWITCHING THE BELT SANDER ON AND OFF (Fig.1)
CAUTION:A sanding belt may have been installed at the factory and the belt tracking may not be set
correctly. Follow steps 5 & 6 in REMOVING, INSTALLING, and ADJUSTING BELTS,below.
CAUTION:Before plugging the tool in,squeeze the trigger once and release it to be sure the
trigger is "Off" and not locked "On".
the handle at the rear.
2. Squeeze the trigger in the rear handle with your index finger to start the tool.
Release it to stop.
3.
4
device when
rot for long hair)
ately switch off the tool and disconnect the plug
Wear dusk mask
Do not dispose of old appliances in the
household garbage
Disconnect from power supply while
maintance
6.Variable speed wheel
GB
REMOVING, INSTALLING,and ADJUSTING BELTS
WARNING: To prevent injury, always switch off and disconnect the tool from power source before
removing or installing the sanding belt.
1.To pull the belt tension lever from the right side of the sander and move it towards the front of the
machine.This pulls the idler(front) pulley back. The old belt can be slid easily off the pulleys.(Fig.2)
have a short-ened life.(Fig.3)
3.To slide a 76"x457" abrasive belt over the front and back pulleys and line it up so that it is centered
is now clamped in place.(Fig.2)
5.To be sure the trigger switch is off.Plug the tool in. The following may be easier if the tool is held
side of the tool or running off the pulleys on the right. The belt should not be more than 6mm (1/4")
as well as damage to the housing will result.(Fig.4)
DUST BAG (Fig.5)
turn the bag inside out and thoroughly clean it with a brush.
SANDING
1.To secure the work piece well. It will tend to move toward the operator while the sander is running in
contact with the surface.
2.To hold the tool firmly with both hands on the hand grips. When the belt comes in contact with the work
surface, the tool will tend to pull itself forward quite strongly. To prevent damage to the material and the
belt, never start the sander while the belt is in contact with the work surface.
3.To turn the tool on and let it come up to speed.
5.To begin moving the sander forward. Drop the back very slightly so the belt contacts the work surface first
with the surface. Use only very light downward pressure, if any.
much weight can result in gouging and burning the surface, overloading the motor, and having the work
piece kick back.
7.When sanding a rough wooden surface, placing the sander at a slight angle to the grain, using a coarse grit,
while moving the sander itself back and forth with the grain, may help speed stock removal. The same
technique can be carried on through the medium grits. On the finishing grits, the sander should be oriented
with the grain.
10.The right side of the sander will allow you to sand flush against a perpendicular surface.
CLEANING AND MAINTENANCE
GB 5