HIGHSIDER PE1-XS Instrucciones De Montaje página 3

Thank you for buying a HIGHSIDER product. Because of our passion for motorcycles all our products are designed to meet your needs as a motorcyclist. We wish you always a safe and pleasant ride with your new HIGHSIDER product
from Paaschburg & Wunderlich GmbH.
Only when professionally installed is the statutory warranty and driving safety fulfilled. Pay attention to the information in the operating instructions of the vehicle or specifications of the vehicle manufacturer. Failure to follow the
assembly instructions can damage your vehicle and void the warranty. This is necessary to not affect the riding safety. No liability is accepted for consequential damage.
The unauthorized reworking and / or modification of the product can lead to the failure of the function and is not permitted. No entry in the vehicle documents or the carrying of any documents is necessary.
Please keep these instructions for later use!
Scope of delivery:
 1 Pair handlebar end with mounting kit (Fig 1)
Assembly of the handlebar
1. Make sure that your motorcycle stands solidly on the ground.
2. Clean the inside of your handlebar.
3. Check the inside diameter of the handlebar (aluminum handlebar 14mm / steel handlebar 18mm).
4. Assemble the parts according to the following figure. (Fig. 2)!
5. Check that the wings of the conical nut H fit inside the slots of the sleeve E1. This will prevent the turning of the sleeve inside of the handlebar during the installation.
ATTENTION: Secure the screw with screw locking (not included)
6. Position the assembly inside the handlebar and turn the screw F1 tight.
ATTENTION: Make sure that the weight C1 does not impair the function of the rotating gas sleeve! A jammed throttle affects the driving safety. Make sure that the steering system and the handlebars with all operating parts can
move freely from other vehicle parts, especially the fuel tank.
Before each ride: It is the duty and responsibility of the rider to regularly check and maintain the safety-related vehicle parts. Before starting your journey, check the correct adjustment and function of the HIGHSIDER products and the tightness of all screwed connections.
Warranty: Take the time to do a 100% professional job of installing the HIGHSIDER products. Take into account all our installation and safety instructions.
A faulty, improper installation or handling of the product will void the warranty.
Maintenance/Care: Do not use aggressive detergents to care for the HIGHSIDER products. The HIGHSIDER products can be perfectly cleaned with a simple, lukewarm detergent solution. Contact with brake fluid, brake cleaner, fuel, etc. should be avoided. Immediately pick
up any unintentionally applied impurities with a soft cloth and clean the surface with detergent solution
Enviromental Information: This product may not be disposed in the normal household rubbish at the end of its lifetime. The disposal can be done through the Paaschburg u. Wunderlich customer service or a local return and waste collection institution.
HIGHSIDER Tips & Tricks on
https://www.youtube.com/c/HIGHSIDERTippsTricks
Exclusion of liability and warranty regulation:
In the event of improper handling, installation or use of the device, warranty and guarantee claims may expire. Due to the non-verifiability of the correct application, Paaschburg und Wunderlich GmbH assumes no liability for direct or indirect damage or consequential damage resulting from the operation of the device.
This does not apply if the damage is based on intent or gross negligence on the part of Paaschburg & Wunderlich GmbH, or if the damage consists in injury to life, limb or health, or Paaschburg & Wunderlich GmbH has culpably violated an essential contractual obligation (cardinal obligation).
Paaschburg & Wunderlich GmbH, Am Alten Lokschuppen 10a, D-21509 Glinde (GER),
Tel.: +49 (0) 40 248 277-0; E-Mail: sales@pwonline.de
161-436A_Rev00_2021-09
Please read this manual carefully prior to installation
Find useful additional accessories like stem extensions, resistors, electronic relays, adapter cables and other equipment in our Webshop!
:
and safety instructions
Mounting
HIGHSIDER PE1 XS/LS handlebar end
You can find more products at:
www.highsider-germany.de
A
A = Ø 37,4mm
www.highsider-germany.de
All rights reserved. Changes and errors are excepted.
Seite 3 von 5