Publicidad
Idiomas disponibles
Idiomas disponibles
Place the unit upright on a sturdy, flat surface. It is equipped with adjustable feet.
• EN 06 1008 fire protection of local energy consumers and heat emitters
• EN 33 2000 (33 2000-4-482; 33 2000-4-42) the environment for electrical appliances
Combustion gas draft
Device type A (see device label)
Type A appliances (appliances not connected to a chimney) must be installed in well-ventilated premises in
accordance with the standards in force, to prevent the accumulation of substances that could harm health in
dangerous concentrations.
Information
4kW burner
Burner diameter 1/100mm
Air Control Settings (mm)
Gas consumption
Burner 4kW 7kW
Main burner diameter
1/100mm
Air Control Settings (mm)
Gas consumption
Information
Burner 4 kW 4 kW
Burner diameter 1/100mm
Air Control Settings (mm)
Gas Consumption
Burner 4kW 7kW
Main burner diameter
1/100mm
Air Control Settings (mm)
Gas consumption
GAS INLET HOSE
Determine if the appliance is suitable for the type of gas used so that it complies with the indications on the
label.
To convert to another gas type, check the correspondence to the gas bearing type.
The connection of the appliance to the gas supply must be made to a steel or copper pipe complying with the
applicable national requirements. The equipment must be checked on a regular basis: change if necessary.
The flexible connection between the plate and the gas installation of the premises must be approved
according to the standards in force. A shut-off valve or tap must be located upstream of the connection hose
to isolate the plate from the gas supply.
After installation, check for possible leaks (use a suitable and approved leak detector).
The device has been checked by the manufacturer, the technical data of the device are mentioned on the
label.
Liquid gas connection:
The gas pressure for the liquid connection must be 28 or 30 mbar for propane / butane and 37 mbar for
propane. It is necessary to check the technical label to assess the pressure and check the parameters of the
installed nozzle.
If the pressure is below 28mbar or above 37mbar, the device must not be connected.
G30
G30
28-30 mbar
37 mbar
100
95
5
5
0.315kg/h
0.315kg/h
135
125
6
6
0.552kg/h
0.552kg/h
G25.1
G2.350
25 mbar
13 mbar
160
210
1.5
1.5
0.491m
/h
0.588m
3
225
300
2.5
2.5
0.860m
/h
0.882m
3
Gas type
G30
G20
50 mbar
20 mbar
90
150
5
1.5
0.315kg/h
0.423m
3
115
205
6
2.5
0.552kg/h
0.741m
3
Gas type
G27
G31
20 mbar
30-37 mbar
175
100
1.5
5
/h
0.516m
/h
0.311kg/h
3
3
245
135
2.5
6
/h
0.904m
/h
0.544kg/h
3
3
G25
G25
25 mbar
20 mbar
160
165
1.5
1.5
/h
0.492m
/h
0.492m
3
215
230
2.5
2.5
/h
0.862m
/h
0.862m
3
G31
37 mbar
50 mbar
95
5
0.311kg/h
0.311kg/h
125
6
0.544kg/h
0.544kg/h
EN
G20
25 mbar
145
1.5
/h
0.423m
/h
3
3
195
2.5
/h
0.741m
/h
3
3
G31
90
5
115
6
Publicidad
