Manuales relacionados para Truper MOE-1/2B
Resumen de contenidos para Truper MOE-1/2B
- Página 1 Manual 1-capacitor 1 725 RPM Single-phase LOW SPEED Motor Applies for: Codes Models 102303 MOE-1/2B 102301 MOE-1/4B Read this manual thoroughly CAUTION before using the tool.
- Página 2 Safety warnings for electric motors using the tool. Parts Keep this manual for future references. Mounting The illustrations in this manual are for reference Connections only. They might be different from the real tool. Troubleshooting Notes Authorized Service Centers Warranty Policy MOE-1/2B MOE-1/4B ENGLISH...
- Página 3 Technical Data MOE-1/2B MOE-1/4B 102303 102301 Code Low speed single phase electric motor with 1 capacitor Description 0.372 kW (1/2 Hp) 0.186 kW (1/4 Hp) Rated power 115 V / 230 V Voltage 60 Hz Frequency 8.8 A / 4.4 A 5.2 A / 2.6 A...
- Página 4 Electric requirements WARNING The equipment must be grounded to prevent electric shock. • Connect the plug into a properly grounded outlet. Not all outlets are properly grounded, if you are not sure, check with a qualified electrician. • If the outlet available for the equipment is a 2-pole (2-hole) outlet, DO NOT REMOVE OR ALTER THE GROUND CONDUCTOR OF YOUR PLUG FOR ANY REASON.
- Página 5 General power tool safety warnings WARNING! Read carefully all safety warnings and instruction listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
- Página 6 Safety warnings for electric motors CAUTION • Before installing or operating the • Tighten the terminal screws to the proper torque to prevent equipment, disconnect from any power source to avoid overheating. electric shock and/or burns due to short circuits. •...
- Página 7 Mounting Motor mounting Shaft joint CAUTION • Before mounting the motor remove • The motor shaft includes a 3/16” (0.5 cm) x 1-3/8” the plastic cover from the shaft and rotate it by hand. (3.5 cm) key to transmit motion to the coupling. The motor shaft must rotate freely.
- Página 8 Mounting • For belt and chain drive applications, verify that the centers of the drive and driven pulleys and/or sprockets are aligned with each other as shown. • Proper alignment and mounting will reduce motor noise and workload vibration. Connections CAUTION •...
- Página 9 Troubleshooting Problem Cause Solution The engine takes a • Defective bearings. • The bearing must be replaced. long time to • Defective capacitor. • Refer to a Authorized Service accelerate. Center for repair. • Faulty stationary switch. • Inspect and repair the switch contacts and connections. •...
- Página 10 Troubleshooting Problem Cause Solution Motor runs, but shuts • Voltage drops. • If the voltage is less than 10% of the motor rating, off. contact the power company. • Check to see if any other equipment is drawing • Load increase. power from the motor and if the motor is running on an extension cord.
- Página 11 Troubleshooting Problem Cause Solution Bearings fail • High ambient temperature. • If the engine is operated in a warm environment, a continuously. different type of bearing grease may be required. Contact Authorized Service Center for a recommendation of the proper type of grease. •...
- Página 12 Notes ENGLISH...
- Página 13 Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800-018-7873 to get information about the nearest Service Center.
- Página 14 It includes the costs of transportation of the product that derive from its fulfillment of its service network. . Phone number 800-018-7873. Made in China. Imported by Truper, S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257, Phone number 761 782 9100.