Hoover POWERDASH Manual Del Usuario página 2

GETTING STARTED
ASSEMBLY
Fully assemble product prior to use.
1
Insert the Upper Handle into Upper Handle Pole
and insert Upper Handle Pole into the base.
You will hear a "CLICK" when each end locks
into place.
2
Slide the Clean Water Tank into place. Push
down firmly.
NOTE:
To avoid damage to wood floors
underneath area rugs or carpet, place
waterproof material (ex: plastic) underneath
them before cleaning..
TIP
BEFORE YOU BEGIN CLEANING
Vacuum carpet and upholstery
1
thoroughly with a Hoover vacuum
before use. Don't use the carpet
cleaner as a traditional vacuum
cleaner.
Test for colorfastness in a small,
2
hidden area. Gently rub surface with
a dampened white cloth. Wait ten
minutes and check for color removal
or bleed with a white paper towel.
OPERATION
FILL THE CLEAN WATER TANK
1
Lift up to remove the Clean Water Tank, then
remove the cap and add warm water to the fill
line. Add Hoover Solution to the solution fill
line. Secure cap.
2
Align the tank and firmly press it into place.
NOTE:
Cap must be locked in place for
proper performance and to prevent leaking.
NOTE:
Read the directions on the
Hoover® Carpet Cleaning fluid prior to use.
CLEANING FLUID
SEE THE HOOVER'S SOLUTION GUIDE insert or visit
Hoover.com/cleaning-solutions.
CAUTION:
Not to be used for
grooming a pet.
CAUTION:
DO NOT USE THIS EXTRACTOR
ON HARD FLOORS. USING THIS PRODUCT ON
HARD FLOORS MAY SCRATCH OR DAMAGE YOUR
FLOOR.
HOW TO CLEAN CARPETS
2 1
1
Step on the Handle Release Pedal to recline the
cleaner for cleaning position.
2
Step on the Power Pedal to turn ON.
IMPORTANT:
Empty Dirty Water Tank
when you hear an audible change. Ensure the
tank is secured before cleaning.
3
Squeeze trigger for a slow forward and
backward wet stroke.
4
Release trigger for a slow forward and
backward dry stroke.
To Rinse: Fill with warm water and omit adding
solution to the Clean Water Tank.
WARNING:
Risk of personal injury –
Brushroll may suddenly restart – unplug before
cleaning or servicing.
HOW TO CLEAN THE DIRTY
WATER TANK
To Dry System: Run system for ten seconds
before shutting off without engaging trigger.
1
Turn power OFF and unplug the power cord.
2
Press down the top of the Dirty Water Tank.
Remove Tank from carpet cleaner base at an
angle.
3
Place on a flat surface and unlatch Dirty Water
Tank lid to remove top of tank.
4
Empty tank, rinse, and allow to air dry.
5
Prior to replacing tank, check and clean filter
as needed.
MAINTENANCE
This product contains no serviceable parts.
If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, call customer service at
1.800.944.9200 prior to continuing use.
HOW TO REMOVE & CLEAN THE
BRUSHROLL AND REMOVE THE
BELT
CAUTION:
To reduce the risk of injury
from moving parts, unplug before servicing.
1
Remove the nozzle cover by pulling up and
forward on the latch. Rinse nozzle cover and
allow to air dry.
2
Gently grab the finger ledge on front of
window, and flip forward. Remove any visible
debris. Flip brushroll cover back in place once
complete.
*
*
in front of wheel
3
Lay the product down to access the underside.
Use a Philips screwdriver to remove 6 screws.
Arrows show location of screws on the
underside of your cleaner.
4
Remove underside belt cover then pull brushroll
out. Belt will still be attached to cleaner.
5
Rinse brushroll and allow to air dry.
6
Slide belt off shaft and remove. If replacing
belt, install the new belt.