Publicidad
Idiomas disponibles
Idiomas disponibles
To remove the battery pack from the tool
Press the release button (13) and firmly pull the battery
u
pack out of the tool handle (Fig. G).
Insert battery pack into the charger as described in the
u
charger section of this manual.
Assembling the pole (Fig. C)
When installing the lower pole (9) into the upper pole (8) ,
u
align the detent lock (14) with the detent slot (15) as
shown in Fig. C.
Press the two poles together so the detent lock (14)
u
engages the detent slot (15).
Warning! Always check to make sure that the detent lock is
completely secured in place. If the detent lock is not
completely secured it could result in the assemblys becoming
disconnected creating a hazardous condition. Periodically
check the connections to insure that the detent lock is
completely secured in place.
Installing the guard (Fig. D, E)
Warning! Never remove the guard. Damage or personal injury
could result.
Warning! NEVER OPERATE appliance WITHOUT GUARD
FIRMLY IN PLACE. The guard must always be properly
attached on the appliance to protect the user.
Remove the guard screw (19).
u
Slide the guard (11) fully onto the motor housing (7). Make
u
sure the tabs (20) on the guard engage the ribs (16) on
the trimmer head.
Continue to slide the guard on until it "snaps" into place.
u
The locking tab (18) should snap into the housing slot
(17).
Using a crosshead screwdriver, insert the guard
u
screw (19) and tighten securely.
Once the guard is installed, remove the covering from the
u
line cut-off blade, located on the edge of the guard.
Adjusting the cutting swath size (Fig. E)
This guard allows for two swath sizes, 280 mm or 330 mm.
To adjust the position of the cutting line blade (88), remove
u
the screws (99) securing the cutting line blade (88) in
place.
Position the cutting line blade (88) to the second position
u
on the guard and secure it with the screws (99).
Note: Moving the cutting line blade (88) closer to the spool
housing will decrease cutting swath size.
Attaching the auxiliary handle (Fig. F)
Remove handle knob (18) and handle bolt (19) from the
u
auxiliary handle (6).
Push the auxiliary handle (6) onto the top of the upper
u
trimmer pole (8) as shown in Fig. F.
Thread the handle bolt (19) through the mounting hole on
u
the auxiliary handle (6).
(Original instructions)
Thread the handle knob (18) onto the handle bolt (19) and
u
firmly tighten. Ensure the handle is secured in position
before using.
To adjust the position of the auxiliary handle, loosen the
u
handle knob (18) and slide the auxiliary handle (6) up or
down the pole until it is in the desired location. Tighten the
handle knob (18) to secure the auxiliary handle (6)
in position.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing (10).
Remove the tape holding the cutting line to the
u
spool housing.
Operation
Instructions for use
Warning! Always observe the safety instructions and
applicable regulations.
Warning! To reduce the risk of serious personal injury, turn
tool off and disconnect battery pack before making any
adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.
Proper hand position (Fig. I)
Warning! To reduce the risk of serious personal injury, Always
use proper hand position as shown.
Warning! To reduce the risk of serious personal injury, always
hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle (5) and one hand on the auxiliary handle (6).
Switching trimmer on and off
Warning! Never attempt to lock the trigger in the on position.
To turn the appliance on, press the lock-off button (2) and
u
then squeeze the trigger (1). Once the unit is running, you
may release the lock-off button.
To turn the appliance off, release the trigger.
u
Speed control switch (Fig. H)
This string trimmer gives you the choice to operate at a more
efficient speed to extend the runtime for larger jobs, or
accelerate the trimmer speed for high-performance cutting.
To accelerate the trimmer, push the speed control
u
switch (3) forward toward the auxillary handle (6) into the
"HI" position. This mode is best to cut through heavier
growth and for applications that need higher RPM.
To extend runtime, pull the speed control switch back
u
toward the battery housing (21) into the "LO" position. This
mode is best for larger projects that require more time
to complete.
Note: When in "HI" mode, runtime will be decreased as
compared to when trimmer is in "LO" mode.
ENGLISH
13
Publicidad
