Function Setting; Care And Maintenance - EDM 08750 Manual De Instrucciones

Cordless impact drill
Operating Instructions
LED light (fig. 6)
A LED light source is integrated in the housing.
The light is activated as soon as the On/Off switch is pressed.
Fully automatic spindle locking (Auto-lock)
When the trigger switch is not pressed, the drill spindle and
the tool holder will be locked. This enables the machine to be
used as a screwdriver, even when the battery is empty.
Run-on brake
When the trigger switch is released, the chuck brakes to a
stop, thus preventing the run-on of the tool. When driving in
screws wait until the screw is screwed in flush with the
material and then release the trigger switch. By doing so, the
head of the screw does not penetrate into the material.

Function setting

Select the torque setting you require. Align the selected
torque setting with the mark at the top of the drillTorque
1-19, Screw function.
Different torque settings for different screws and materials,
please see 'Torque adjustment'.
Hammer function. Only for hammer, torque setting
is useless.
Drill function. Only for drill, torque setting is useless.
Operation for working
1. General drilling
Before use for drilling, the torque setting should be set on
drill position " ".
- Your cordless drill is useful for drilling holes as well as driving
and removing screws.
- Use the correct speed for the job; do not try to drill on a slow
speed; similarly do not try to driver screws on a high speed.
- To prolong the life of your drill never overload it; if it slows
down while drilling, remove and trying again using less force
on the drill. If the drill is straining because the battery pack
charge is low, stop and recharge the battery pack.
- Use slow speed for starting holes without a centre-punch,
drilling metals or plastics, driving screws, and drilling
EN INSTRUCTION MANUAL
ceramics, or any application requiring high torque. Use higher
speeds for drilling wood and when using polishing
accessories. For maximum drill life use the variable speed
control but do not use it continuously in the variable speed
range.
2. Hole drilling
- When attempting to drill a large diameter hole, it is
sometimes best to start with a smaller drill bit then work up
to the required size. This prevents overloading the drill.
- If the drill bit snags, switch off the drill immediately to
prevent permanent damage. Try the reverse drive to remove
the bit.
- Keep the drill in line with the hole. Ideally, if the angle is
changed during drilling it could cause the bit to break,
blocking the hole and perhaps causing injury.
- Frequently remove the drill bit from the hole when drilling
deep holes to allow the dust to be ejected from the hole.
3. Screw driving
- When driving in larger and/or longer screws in hard material,
it is advisable to drill a pilot hole first, slightly longer and just
smaller than the shank diameter of the screw to be fitted. The
pilot hole will act as a guide for the screw and will also make
tightening of the screw less difficult. When screws are
positioned close to an edge of the material, a pilot hole will
also help to prevent splitting of the wood.
- Use only screwdriver bits that fit properly in the head of the
screw.
- When driving screws, always keep enough pressure on the
drill to prevent wearing of the screw head. It will be difficult to
drive or remove a screw if the screw head is worn.
4. Deep discharge protection
This cordless drill is integrated deep discharge protection,
when the tool was used heavily, the discharge protection will
operate to cut off inner circuit, after the a few time rests,
discharge protection will reset.

Care and Maintenance

Keep the ventilation openings clear and clean the product
regularly. This machine requires no special mechanical
maintenance such as greasing the bearings.
If something unusual occurs during use, switch off the supply
and remove the battery pack. Inspect and repair the tool
before using it again. The repairs must be carried out by a
qualified technician.
Repair of the tool must only be carried out by a qualified
repair technician.
Repair or maintenance by unqualified personnel can lead to
a risk of injury.v
REF. 08750