Publicidad
Idiomas disponibles
Idiomas disponibles
USER MANUAL
AeroFlow® Surface storage heater with FlexiSmart thermostat
possible replacement of the radiator side part (e.g. when changing the
control technology) and / or the possible shortening of the connecting
cable (e.g. removal of the earthed plug for the purpose of producing
a fixed connection) does not lead to a loss of warranty, insofar as no
intervention in or manipulation of electronic components takes place,
beyond the necessary extent of the modification to be performed, and
the correspondingly permissible work is performed by a qualified expert.
The warranty covers the careful inspection of the radiator or the acces-
sories whereby it must be initially determined whether a warranty claim
applies. In the event of a claim under the warranty we solely decide in
which manner the fault shall be rectified. We are at liberty to replace a
radiator or accessory or to perform a repair. During the warranty period,
we assume all material, assembly and transport costs within the scope
of this warranty.
In addition to the above-mentioned warranty service, the end customer
cannot assert any claims for indirect damage or consequential damage
caused by the device, in particular for compensation for damages incur-
red outside the device. Statutory claims of the customer against us shall
remain unaffected by this clause. Warranty claims must be reported to
us before expiry of the warranty period, within one week of the defect
being detected.
Fixing the wall brackets
3
Only the wall bracket supplied may be used for wall mounting! The
latest regulations according to VDE 0100 part 701 must be complied
with for the installation and operation in damp rooms.The device may
not be mounted directly under a wall socket. In order to avoid excessive
heat radiation upon the wall socket, a certain safety distance must
also be taken into account between the radiator and the wall socket.
This distance is largely determined by the material quality and heat
resistance of the locally installed socket and therefore can not be
assessed by us. We assume no liability for improper handling and
possible damages resulting from this. In case of doubt, consult a
specialist before installation. Suitable screws and dowels must be
used depending on the type and condition of the wall material. When
positioning the wall bracket and the heater, please always observe the
stipulated minimum distances (see the following figures).
10 cm
Mounting dimensions
8 cm
All radiators have four temperature-resistant holders, which guarantee
optimum fixing of the heater. Please note the correct hanging position
of the upper (marking 1) and lower (marking 2) holders on the heater.
above
Hanging part
below
With the type-specific dimension table, you can obtain the correct
positioning for the U-rails and the holders for the correct mounting and
fixing of the radiator.
VD010 V3, valid from firmware v220826
Measure X
90 mm
Measure Y
90 mm
190 mm
Lamellas
Lamellas
Hanging part
Radiator type
Dim X in mm
Mini 650
Compact 1300
Midi 1950
Maxi 2450
Slim 1200
Slim 2000
Slim Tall 1600
For the assembly please perform the following steps:
1. The two U-rails must be fixed to the wall whilst observing
the minimum distances and depending on the type-specific
X / Y-dimension.
2. The two holders marked with the number 2 are to be inserted
into the U-rails at the bottom.
3. Following this the radiator is hooked into the lower holders and
tilted forward at an angle. Hold the radiator while doing so!
4. The two holders marked with the number 1 are to be inserted
into the U-rails at the top and temporarily pulled up.
5. Finally, place the radiator in a vertical position and press the
upper holders down until the heater is completely fixed in place.
German battery legislation
Since batteries and rechargeable batteries may be included in our
consignments, we are obliged by the German battery legislation (BattG)
to point out the following: Batteries and rechargeable batteries must
not be disposed of with household waste, but you are legally obliged
to return used batteries and rechargeable batteries. Used batteries may
contain harmful substances which, if not properly stored or disposed
of, could damage the environment or your health. But batteries also
contain important raw materials such as iron, zinc, manganese or nickel
and can be recycled. You can either return the batteries to us after use or
return them free of charge in the immediate vicinity (eg in stores or in
municipal collection points). The discharge in points of sale is limited
to end user customary amounts and such batteries that are sold or have
been sold from the distributor as new batteries in his assortment.
Note - alignment of the temperature sensor
The temperature sensor is attached to the bottom of the radiator in
a clip. If, due to the placement of the device in a niche or corner, the
room temperature and the measured temperature is influenced, the
sensor can be removed from the clip. The distance to the radiator can be
increased by turning the connection cable of the sensor. The best way to
correct the temperature is in the menu settings, „temperature correction".
Smart Start (adaptive start control)
With this function, the desired room temperature is met at the start time
of the program. This means that the heater is already heating before
the set start time. This is not a malfunction! Smart Start can only be
used in program mode. You can deactivate Smart Start in the menu item
„Programs". When Smart Start is deactivated, the electric radiator starts
heating when the preset start time is reached.
Learning phase: In order to reach the target temperature exactly at the
start time of each programmed time frame, your FlexiSmart performs
a learning phase in the first seven days. During this time, heating is
always started 15 minutes before the set start time (in every single
time window). As a result, the FlexiSmart controller learns how fast or
slow heating takes place in the room and adjusts the „smart start time"
of heating. After the learning phase, the FlexiSmart controller decides
when to start heating up. Your rooms will be heated up as effectively
as possible.
Switch daylight saving time to standard time
The FlexiSmart controller does not have an automatic changeover
between daylight saving time to standard time. You must change the
time manually in the „Set the time" menu. Exception: If the FlexiSmart
controller is connected to an internet module, an automatic changeover
takes place between daylight saving time to standard time.
9
Dim Y in mm
232
405
466
405
766
405
1066
405
766
120
1366
120
232
1040
www.thermotec.ag
Publicidad
