Profi Cook PC-EWB 1253 Manual De Instrucciones página 9

Warnings for the Use of the Appliance
WARNING:
The refrigerant circuit of the appliance uses the refrig-
erant isobutane (R600a), a flammable natural gas with
high environmental sustainability. When transporting and
installing the appliance, prevent the appliance from falling
down. The refrigerant circuit must not get damaged.
CAUTION:
Please observe a waiting period of 2 hours before initial
operation and after moving the appliance for the refriger-
ant to settle. Otherwise the compressor can be damaged.
If the Refrigerant Circuit is Damaged
• Open flames and ignition sources must be avoided.
• Disconnect the mains plug.
• Ventilate the room in which the appliance is installed.
Notes for Use
Location
• Place the appliance on a stable, horizontal, water-resist-
ant and level surface. Maintain a gap of at least 15 cm to
walls or objects.
• Do not place the appliance on or directly next to heat
sources such as ovens, radiators, etc.
Electrical Connection
1. Before inserting the plug into the socket. Make sure that
the mains voltage to be used matches that of the appli-
ance. You can find this information on the nameplate.
2. Connect the appliance to a properly installed wall outlet.
Standby (Standby Mode)
If no control lamp is lit, the appliance is in standby mode.
Ice Cube Size
You may choose between 2 sizes:
- small ( – small icon)
- large ( – large icon)
Eco Save (Power Saving Mode)
Once the ice cube container is full the appliance switches
into standby mode.
You benefit from better safety and lower energy consump-
tion.
Operation
When using the appliance for the first time or if you have not
used it for a long time, clean the appliance as described in
the chapter "Cleaning and Maintenance".
PC-EWB1253_IM
Making Ice Cubes
1. Make sure that the water tank cap on the bottom of the
appliance is tightly closed.
2. Open the lid and take out the ice cube container.
3. Fill the container with water to no more than the MAX
mark. Only use drinking water to make ice cubes.
- For best results, aim for a water temperature of
between 7 °C and 20 °C as well as an ambient tem-
perature of between 16 °C and 25 °C.
- If you want clear ice cubes, use chilled drinking water
which has firstly been boiled.
4. Now put the ice cube container back in and close the lid.
5. Press the button to start ice cube production.
6. Select the desired ice cube size with the
corresponding control lamp lights up.
- For hygienic reasons do not use the ice cubes from
the first cycle.
- The first few ice cubes will be small depending on the
water temperature and ambient temperature. The ice
cubes will only grow larger in the following cycle.
- Due to fast freezing the ice cubes can look "milky".
This is the air trapped in the water and does not influ-
ence the quality of the ice cubes.
7. Keep the lid closed during ice cube production. An ice
cube making cycle lasts between 9 and 10 minutes.
Stop Ice Cube Production
Press the button to stop ice cube production.
- If operation is manually interrupted, water which is no
longer needed is fed back to the water tank. Only then
will the appliance stop. Half-finished ice cubes remain
suspended on the cooling rods. As soon as it is suffi-
ciently thawed, it will fall off and drop into the ice cube
container.
Control Lamp (Ice Cube Container Full)
As soon as the ice cube container is full, the sensor stops
production.
The control lamp flashes. The appliance switches into
standby mode.
• Remove the ice cubes with the supplied ice cube scoop.
When removing the ice cube container, some water will
drip through the holes onto the floor.
• The control lamp turns off and a few moments later
ice cube production starts again.
Control Lamp (Water Refill)
The control lamp displays when there is too little water
in the water tank. Ice cube production is automatically
interrupted.
1. Press the button to switch off the appliance.
2. Open the lid.
3. Empty the ice cube container.
button. The
9
31.08.22