Clatronic BS 1313 Manual De Instrucciones página 11

• The latches on the appliance must be in the recesses
of the motor housing. Press the motor housing onto the
collection container until the latches engage.
Connect and Disconnect the Hose
Suction Function
Insert the hose connection into the suction opening on the
collection container. Pay attention to the recesses. Turn the
hose clockwise to tighten.
Fan Function
Insert the hose connection into the blow-out opening on the
motor housing. Pay attention to the recesses. Turn the hose
clockwise to tighten it.
Loosen the Hose
Loosen the hose by turning it anticlockwise and pulling it out.
3-part Suction Tube
• Insert the two suction pipes into each other without the
holder.
• Insert the thinner end of the assembled suction tubes
into the thicker end of the suction tube with holder.
• To detach the suction tubes, pull them off while turning
them slightly.
Nozzle Attachments
• To detach the nozzle attachments, pull them off with a
slight twist.
• There are several ways to store the brush nozzle and
crevice nozzle.
- Use the holders above the rollers or the holders on
the lid.
Floor Nozzle
You can clean smooth surfaces and carpets dry or wet with
the floor nozzle. The floor nozzle is equipped with rollers for
easier guidance.
• Use the lever to move the brushes outwards or inwards.
The optimal use depends on the condition of the floor. We
recommend the following use:
• Use without Brushes (
- For vacuuming dry carpets (high pile).
- For cleaning wet, smooth floors.
This setting is also best suited for picking up water
from larger areas.
Note that the collection container can only hold a
limited amount of liquid! The maximum filling quantity
is reduced accordingly for foam-forming additives!
• Use with Brushes (
- For vacuuming dry, smooth floors and dry carpets
(low pile).
- For cleaning (scrubbing) wet, smooth floors and wet
carpets (low pile).
BS1313_IM_new - SH separat
):
):
Crevice Nozzle
For vacuuming in corners and slits, etc.
Brush Nozzle
For cleaning upholstery or curtains.
Air Slider
Open the air slider on the hose handle to regulate the air or
to loosen parts sticking to the nozzle.
Mains Cable
• For operation, unwind the mains cable completely.
• After operation, let the motor housing cool down first. You
can then wrap the mains cable around the motor housing.
Switching On / Off
Use the on / off switch to turn the appliance on (I) and off (O).
Using the Appliance
Preparation
1. Select the desired accessory.
2. Unwind the mains cable completely.
3. Check that the mains voltage you want to use corre-
sponds to the information on the rating plate.
Vacuuming Dry
1. Place the permanent filter in the collection container.
2. Place the motor housing with the recesses on the latches
until they click into place.
3. Fit the accessories.
4. Insert the mains plug into a properly installed earthed
socket.
5. Switch on the appliance.
6. Now vacuum at a steady speed. It is not necessary to
press down.
Wet Vacuuming
1. Pull the mains plug out of the socket.
2. Remove the permanent filter. Insert the sealing ring
instead.
3. Fit the sealing ring over the edge of the collection unit.
4. Place the motor housing with the recesses on the latches
until they click into place.
5. Fit the accessories.
6. Insert the mains plug into a properly installed earthed
socket.
7. Switch on the appliance.
The collection container can only hold a limited amount
of liquid! If foam forms in the collection container, the
maximum collection volume is reduced accordingly!
When the container is full, the float valve closes the
suction opening and the motor runs at increased speed.
Switch off and empty the appliance immediately.
11
13.02.23