Master PROHEAT STC PH-1600 Manual De Instrucciones página 2

Important Safety Instructions
Heat guns are a source of extremely high-tem-
perature flameless heat (up to 1050˚F / 566˚C).
Extreme caution should be observed when using
these products. READ and FOLLOW these
instructions.
Use only on properly-rated electrical
circuits.
Connect to properly grounded outlets
only.
Disconnect from power source during
service and when replacing parts.
120V/15A 230V/8A
To reduce risk of fire or electric
shock, do not expose heat gun to
rain or moisture.
Store indoors.
Do not use near flammable materials
or where fumes, gases or dust are
present.
Do not use in presence of explosive
atmosphere.
Keep nozzle at least 1"/2.5 cm from
work surface.
Do not apply to the same place for a
long time.
Be aware that heat may be conducted
to combustible materials that are out
of sight.
Use in well-ventilated area.
Use caution in confined areas.
Do not leave heat gun unattended
when it is switched on.
Place heat gun on its stand after
use and allow it to cool down before
storage.
2
All manuals and user guides at all-guides.com
Caution! Laser radiation. Do not stare
into beam. Class 1 laser product.
When using an extension cord, use
only a 3-wired grounded cord rated
equal to or greater than the appliance.
Connect to properly grounded outlets
only.
120V/15A 230V/8A
Keep away from children and persons
with reduced physical, sensory or
mental capabilities or lack of experi-
ence or knowledge.
Do not direct air stream at people
or pets.
Do not drop.
Wear safety glasses at all times.
Do not touch nozzle until cool.
Recycle properly.
www.masterappliance.com
Introduction, Product Warranty
& Speciications
Introduction
Master's ProHeat STC is the first heat gun of its kind that has the abilit
the temperature of the work surface. This is done by set
on the LCD and watching the actual work suface temper
target temperature. The ProHeat 1600 is perfect for use on t
of all types where heat control is needed. The ProHeat 1
gun technology a step further and allows the user to toggle bet
sensing mode and the traditional nozzle control heat gun mode
Whether you chose the PH-1600 or PH-1610, be sure t
with the safety and operating instructions inside this man
Product Warranty
Master Heat Tools are carefully tested and inspected bef
We warrant our products to be free from defects in mat
use and service, for one year from date of purchase. In the e
workmanship we will either repair or replace, without char
our judgement shows evidence of such defect.
Warranty does not apply to wearable items such as at
solder tips, heat tips, burners or ejectors, which requir
apply if the heat tool has been misused, abused, tamper
At the end of the warranty period, Master Appliance shall be under no fur
expressed or implied. Master Appliance assumes no r
not cover, any incidental or consequential damages fr
This warranty gives you specific rights. You may also ha
state to state. Warranty information is included within the Instr
or may be obtained by contacting Master's Customer Ser
Master Appliance Corp.
Attention: Repair Department
2420 18th Street
Racine, WI 53403-2381
USA
Features
Variable Variable Digital
Airflow Temp. Display
Model Name
Model No.
ProHeat STC
PH-1600 , PH-2600
ProHeat STC Dual Mode
PH-1610 , PH-2610
Specifications
Model Max Max Temperature Set
V ac Hz
No.
Watt Amp
PH-1600
120 60 1426 11
PH-1610 90 - 500˚F
40 - 270˚C
PH-2600
230 50/60 1320 6.8
PH-2610
Note:
www.masterappliance.com
262-633-7791
800-558-941
sales@mast
www.mast
Lock
Controls
Mode
170 - 1000
80 - 540
-models PH-1610, PH-2610 only