stayer CPT 3000 E Manual De Instrucciones página 24

Not using the guide rail = guide rail depth adjustment
stopper up.
(Fig. 3)Tighten the cutting depth limit stop knob (9). The
motor or respectively the saw blade can now be pushed
down to the set cutting depth.
For a clean, safe cut set the cutting depth in such way that
only max. one saw blade tooth protrudes under the work
piece.
Setting the cutting angle (Fig. 4)
The plunge saw can be swiveled between 0° and 48°:
- Loosen both rotary knobs (8). Swivel the motor to the
desired cutting angle on the cutting angle scale.
- Tighten the rotary knobs (8) again
Always hold the plunge saw with both hands.
Always guide the plunge saw forward. Never
draw the plung saw back!
Determine Cutting line (Fig. 4)
Two cutting lines are marked on the base plate (5) of the
plunge saw.
- Align position A (0 mark on base plate) at the front of the
base plate with your marked cutting line when using the
plunge saw without guide rail for straight cuts.
- For 45° miter cuts align position B (45 mark on base plate)
at the front of the base plate with your marked cutting line.
Straight cuts (90° cut)
Loosen both rotary knobs (8) and swivel the saw to 0°
position on the scale. Tighten the rotary knobs again.
Turn the selector switch (17) to plunge cut function.
- Set the desired plunge depth. Ensure that the
guide rail depth adjustment stopper (10) is up when
using the saw without guide rail.
- To switch on the saw press the switch lock (2) and the
ON/OFF switch (1) and push the motor down. Guide
the saw forward to cut.
Miter cuts (up to 48°)
- First loosen both rotary knobs (8) and swivel the plunge
saw to the desired graduation. Tighten the rotary knobs
again.
- Switch the plunge saw on.
Turn the selector switch (17) to plunge cut function.
- Set the desired plunge depth. Ensure that the guide rail
depth adjustment stopper (10) is in up position when
using the saw without guide rail.
To switch the saw on press the switch lock (2) and the ON/
OFF switch (1) and push the motor down. Guide the
saw forward to cut.
The cut indicator (14) shows the cutting path for 90°
and 45° miter cuts (without using the guide rail).
Marked cutting
Turn the selector switch (17) to marked cut
function.
ENGLISH
24
- Press the switch lock (2) and push the motor down.
The casing stops in 2.5 mm cutting depth position.
Note: The marking line should be aligned with cutting line
A (0 mark).
Plunge cuts
- For a straight cut first loosen both rotary knobs (8)
and swivel the plunge saw to 0° position on the scale.
Tighten the rotary knobs again.
Turn the selector switch (17) to plunge cut function.
- Set the desired plunge depth. Ensure that the guide
rail depth adjustment stopper (10) is up if not using the
guide rail.
- Press the switch lock (2) and the ON/OFF switch (1)
and push the motor down. Guide the saw forward to
cut.
Note: To prevent the saw from kicking back during plunge
cuts follow these steps:
- Always place the plunge saw with the rear edge of the
base plate (5) against a fixed limit stop.
- Hold the plunge saw in both hands and slowly lower
the saw blade.
- The cutting width marks (15) show the most foremost
and rearmost cutting points of the saw blade (Ø 185
mm) at maximum cutting depth and when using the
guide rail.
Replacing the saw blade
Before any maintenance work always switch off
the plunge saw and disconnect from mains
power.
- Loosen both rotary knobs (8) and swivel
the plunge saw to 0° position before changing the saw
blade. Tighten the rotary knobs again.
- Set the selector switch (17) to the change saw
blade icon.
- Press the switch lock (2) down and push
the motor down.
- Press and hold the spindle arrester down.
- Use a 5 mm Allen key to turn the screw at the saw
blade slightly clockwise or counter-clockwise until the
spindle clicks into place.
- Use the Allen key to loosen the screw counter-
clockwise. Remove the outer flange and the saw blade.
- Clean both flanges and replace the saw blade.
Note: The rotation direction arrows of saw blade and saw
must be aligned!
- Replace the outer flange in such way that the slaving
pins sit in the recesses of the inner flange.
- Press and hold the shaft lock b utton and tighten the
screw. Press the switch lock (2) for the casing to swivel
up again.
FINE ADJUSTMENT OF PLUNGE SAW PLAY ON
GUIDE RAIL
The play of the base plate on the guide rail can be reduced
to minimum with the fine adjustment screws (7).
- Loosen the fine adjustment screws counter-clockwise.
24