Technical specifications for rechargeable
battery
– Nanophosphate
high-power lithium-ion
®
rechargeable battery, cadmium-free LiFePO
– Can be recharged at any time without shortening
battery lifespan.
– Automatic recharging by solar panel.
– Can be recharged using charging adapter at
micro USB socket (5 V).
– Can be replaced by the manufacturer or
qualified electricians.
– Rechargeable battery capacity: 2500 mAh
– Max. lighting duration:
60 days at 20 switching operations a night.
– Micro USB charging socket: 5 V, 1 A max.,
can be used in all three programmes.
Recharging time depends on the site of installa-
tion (direct sunlight). Expect charging to take many
times longer in winter or on rainy days.
Accessories
– Replacement 6 m extension cable for XSolar
EAN/UPC code 4007841006518
4. Installation
• Check all components for damage.
• Do not use the product if the solar panel or
LED panel is damaged.
Operating reliability will be limited if the product is
used in adverse conditions (e.g. installed in shade
or behind glass, solar panel not facing the right
direction)
• Choose an appropriate site with plenty of sun-
light for installing the solar panel (facing south).
• Avoid shade from porches, overhanging roofs
or trees.
• Pay attention to detection reach (Ill. 4.1).
• Remove wall mount (Ill. 4.2).
• Drill holes and fit rawl plugs (Ill. 4.3).
• Screw-fasten wall mount to the wall (Ill. 4.3).
• Make settings (Ill. 4.4).
➔ "6. Operation"
• Screw SensorLight to wall mount (Ill. 4.5).
• Aim LED panel with motion detector in the right
direction (Ill. 3.4).
• Aim solar panel to get the strongest sunlight for
the longest time possible (Ill. 3.4).
• Check compass (for south-facing position)
(Ill. 3.4).
5. Optional
Install LED and solar panel separately
To optimise conditions at the point of use, the solar
.
4
panel and LED panel can be mounted separately
(Ill. 5.1).
– LED panel: light where it's needed.
– Solar panel: exposed to a high level of direct
sunlight.
Risk of damage to property
Pulling on the cable can cause irreparable damage
to the product.
• Route the cable out of children's reach.
• Remove wall mount (Ill. 5.2).
• Separate solar panel from LED panel (Ill. 5.3).
• Drill holes and fit rawl plugs (Ill. 5.4).
• Route extension cable behind wall mount
(Ill. 5.4).
• Screw-fasten wall mount to the wall (Ill. 5.4).
• Connect extension cable to solar panel (Ill. 5.5).
• Fit solar panel holder to solar panel (Ill. 5.5).
• Screw solar-panel to wall mount (Ill. 5.6).
• Pull extension cable downwards (Ill. 5.6).
• Drill holes and fit rawl plugs (Ill. 5.7).
• Route extension cable behind wall mount
(Ill. 5.7).
• Screw-fasten wall mount to the wall (Ill. 5.7).
• Connect extension cable to LED panel (Ill. 5.8).
• Fit LED-panel holder cover to LED panel (Ill. 5.9).
• Make settings (Ill. 5.10).
➔ "6. Operation"
• Screw LED panel to wall mount (Ill. 5.11).
• Pull extension cable downwards (Ill. 5.11).
• Aim LED panel with motion detector in the right
direction (Ill. 3.4).
• Aim solar panel to get the strongest sunlight
for the longest time possible (Ill. 3.4).
• Check compass (for south-facing position)
(Ill. 3.4).
6. Operation
Before using for the first time
• Activate light by setting the programme selector
switch to P2.
The light stays in test mode for one minute
before it starts to work in programme P2.
Test mode
During the test sequence the light works in
daytime mode.
On detecting movement, the light switches ON
for 1 minute with a stay-ON time of 10 sec. irre-
– 11 –
– 11 –