enbrighten ZWA4011ENB Manual

FCC/IC
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Important note: To comply with the FCC RF exposure compliance requirements, no change to the antenna
or the device is permitted. Any change to the antenna or the device could result in the device exceeding
the RF exposure requirements and void user's authority to operate the device.
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils exempts de
licence d'Industrie Canada. Son utilisation est sujette aux deux conditions suivantes : (1) cet appareil ne doit
pas occasionner de brouillage préjudiciable et (2) cet appareil doit accepter toutes les interférences reçues,
notamment les interférences qui peuvent provoquer un fonctionnement non désiré.
NOTE DE LA FCC : Le fabricant n'est pas responsable des interférences sur les fréquences radioélectriques
ou télévisuelles pouvant être causées par des modifications non autorisées de ce matériel. De telles
modifications peuvent annuler le droit de l'utilisateur à utiliser cet appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils numériques
de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont été définies afin de fournir
une protection raisonnable contre le brouillage préjudiciable en milieu résidentiel. Cet appareil produit,
utilise et peut émettre des ondes de fréquence radio et, s'il n'est pas installé et utilisé conformément aux
instructions, il peut provoquer un brouillage préjudiciable aux communications radio. Il n'existe toutefois
aucune garantie que des interférences ne se produiront pas au sein d'une installation donnée. Si cet
appareil occasionne un brouillage préjudiciable à la réception radiophonique ou télévisuelle, il suffit
d'allumer et d'éteindre l'appareil pour déterminer sa responsabilité. Nous encourageons l'utilisateur à
essayer de corriger ces interférences en appliquant une ou plusieurs des mesures suivantes :
— Réorienter ou déplacer l'antenne de réception.
— Augmenter la distance entre l'appareil et le récepteur.
— Brancher l'appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant l'exposition
aux RF, aucune modification apportée à l'antenne ou au dispositif n'est autorisée. Toute modification
apportée à l'antenne ou au dispositif pourrait faire en sorte que le dispositif dépasse les exigences
d'exposition aux RF et pourrait annuler le droit de l'utilisateur à utiliser ce dispositif.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las
especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá aplicables
a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos condiciones: (1)
este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo debe aceptar
toda interferencia que reciba, incluso la que pudiera causar un funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio
o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas
modificaciones podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B, de
conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para proveer
protección razonable contra interferencias perjudiciales en una instalación residencial. Este equipo genera,
usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa según las instrucciones, puede
provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no hay garantías de que no
ocurrirá interferencia en una instalación en particular. Si este equipo provoca interferencia perjudicial a
la recepción de radio o televisión, lo que puede determinarse encendiendo y apagando el equipo, se
recomienda que el usuario intente corregir la
interferencia por medio de la implementación de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente
del circuito al que está conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier
cambio a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de
exposición de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.
Responsible Party - US Contact Information | Parte responsable - Información de contacto de los
Estados Unidos | Partie responsable - Coordonnées des États-Unis
ZWA4011ENB:
FCC ID: QOBZWA4011 | IC: 6924A-ZWA4011 FCC ID: QOBZWA4011ENB | IC: 6924A-ZWA4011ENB FCC ID — QOBZWA4011ENB | IC: 6924A-ZWA4011ENB
Jasco Products Company | Model: ZWA4011ENB/58433
10 E. Memorial Rd., Oklahoma City, OK 73114 | 1-800-654-8483
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks of their MADE IN CHINA/FABRIQUÉ EN CHINE/
respective owners. HECHO EN CHINA
Tous les noms de marque illustrés sont des
DISTRIBUTED BY
marques de commerce de leurs propriétaires
JASCO PRODUCTS COMPANY LLC,
respectifs.
10 E. MEMORIAL RD.,
OKLAHOMA CITY, OK 73114.
Todas las marcas que aparecen aquí
son marcas registradas de sus respectivos ©JASCO 2021 | 58433 | ZWA4011ENB | 07/08/21 v1
dueños.
1. 1.
Tools you will need
IMPORTANT!
The fixture controlled by the Z-Wave in-wall smart switch must not
exceed 960W incandescent, 1800W (15A) resistive or 1/2HP motor. The
switch is designed only for use with permanently installed fixtures.
Getting to know your new Z-Wave device
• Turn ON/OFF manually or remotely via the Z-Wave controller
• Can be added in multiple groups and scenes
• May be used in single-pole installation or with up to four add-on switches
(model 46199/59339) in 3-way or 4-way wiring configurations
• Compatible with all incandescent and CFL/LED bulbs
• Auto line/load detection
• Interchangeable paddle switch — white & light almond paddle in package
• Uses a standard, rocker-style wallplate for single-gang installations
(wallplate not included)
• Multicolor LED indicates switch location in a dark room
• Z-Wave certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for line (hot), load,
neutral and ground. Traveler wire required for 3-way or 4-way installation
• This Z-Wave device has advanced features that allow you to customize
your experience. These features can only be adjusted by a Z-Wave enabled
controller that supports the Z-Wave configuration command class. For a
complete list of adjustable configurations, visit www.ezzwave.com/config
2. 2.
A
B D
F
G
C
E
A. Ground (Green/Bare) F. Top rocker — press
to turn switch ON
B. Line or Load (Black)
G. Bottom rocker — press
C. Line or Load (Black)
to turn switch OFF
D. Traveler (Red/Other)
E. Neutral (White)
MANUAL • MANUEL • MANUAL
In-Wall
READ IT OR WATCH IT
Smart Switch
Montage Mural
Intelligent Enfichable
Read instructions or watch easy-to-follow video.
Interruptor
Scan QR code or visit https://byjasco.com/58433i
De Pared
Inteligente
Convert any smart control* to a multi-location switch
*For a list of compatible devices, visit ezzwave.com
Smart control Add-on switches
To purchase an add-on switch or for more
details, visit ezaddonswitch.com.
Multiple paddle
colors available
ezzwave.com/paddlecolors
Purchase additional items at
EZzwave.com or visit your local retailer.
In-Wall Plug-in
Smart Dimmers Smart Dimmers Add-on Switches
In-Wall Motion Plug-in
Switch or Dimmer Smart Switches
Smart Switches
In-Wall Tamper-Resistant In-Wall Plug-in Outdoor
Smart Outlet Smart Switch
Smart Fan Control
3. 3.
OR
OR
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture
at the service panel. All wiring connections must be made with the POWER
OFF to avoid personal injury and/or damage to the switch. This device is
intended for installation in accordance with the National Electric Code and
local regulations in the United States or the Canadian Electrical Code and local
regulations in Canada. If you are unsure or uncomfortable about performing
this installation, consult a qualified electrician.
Multi-switch wiring
For 3-way installations, please refer to add-on switch (46199/59339) manual.
Single-switch wiring
Before installation, you may wish to change the paddle color to match your wallplate
or décor. Please proceed to section 5.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
5. There are up to five screw terminals on the switch; these are marked:
A. GROUND — Green/Bare
B. LINE OR LOAD — Black (connected to power or lighting)
4. 4.
Adding your device to a Z-Wave network To remove and reset the device
1. Follow the instructions for your Z-Wave certified
1. Follow the instructions for your Z-Wave certified controller
controller to add a device to the Z-Wave network.
to remove a device from the Z-Wave network.
2. Once the controller is ready to add your device, press the
2. Once the controller is ready to remove your device, press
top or bottom of the wireless smart switch (rocker).
the top or bottom of the wireless smart switch (rocker).
You have complete control to turn your fixture
To return your switch to factory defaults
ON/OFF according to groups, scenes, schedules and
interactive automations programmed by your controller. 1. Quickly press ON (top) button three times, then immediately
press the OFF (bottom) button three times. The LED will
If your Z-Wave certified controller features remote access,
flash ON/OFF five times when completed successfully.
you can control your fixture from your mobile devices.
NOTE: This should only be used if your network's primary
If prompted by the controller to enter the S2 security code, refer
controller is missing or otherwise inoperable.
to the QR code/security number on the side of the box or the QR
NOTE: SmartStart enabled products can be added into a
code label on the product (see Figure 1). Enter the 5-digit code.
Z-Wave network by scanning the QR code on the product with
Figure 1:
a controller providing SmartStart inclusion. No further action is
DSK : Z-WAVE DSK
required and the SmartStart product will be added automatically
XXXXX
-25651-22671
within 10 minutes of being switched on in the network vicinity.
-26939-47599
-19612-25872
PIN: XXXXX
-47752
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between
7AM-8PM, M-F, Central Time.
For the most up-to-date product support, accessories, electronic (PDF) format
manuals and more, visit www.byjasco.com/support.
• No user-serviceable parts in this unit.
Des questions? Contactez notre Service Consommateurs basé aux États-Unis au
1-800-654-8483 entre 7 h et 20 h, H-F, heure central
58433
Pour le soutien relatif aux produits le plus à jour, les accessoires, les manuels en
ZWA4011ENB
format électronique (PDF) et plus encore, visitez le site www.byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l'utilisateur.
Preguntas? Póngase en contacto con nuestro Servicio de Atención al
Consumidor con sede en EE. UU. Al 1-800-654-8483 entre las 7AM y las 8PM,
de lunes a viernes, hora central.
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support.
• Esta unidad no contiene piezas que el usuario pueda reparar.
WARNING
RISK OF FIRE RIESGO DE INCENDIO
RISK OF ELECTRICAL SHOCK RIESGO DE DESCARGA ELÉCTRICA
RISK OF BURNS RIESGO DE QUEMADURAS
CONTROLLING APPLIANCES CONTROL DE EQUIPOS ELECTRODOMÉSTICOS
CAUTION: PRECAUCIÓN:
• DO NOT EXCEED RATINGS • NO SUPERE LOS VALORES
NOMINALES ELÉCTRICOS
• DO NOT USE TO CONTROL ANY DEVICE
WHERE UNINTENDED OPERATION • NO USAR PARA CONTROLAR DISPOSITIVOS
COULD CAUSE UNSAFE CONDITIONS EN LOS QUE EL FUNCIONAMIENTO NO
(HEAT LAMP, SUN LAMP, ETC.) INTENCIONADO PODRÍA PROVOCAR
SITUACIONES PELIGROSAS (LÁMPARAS DE
• DO NOT USE TO CONTROL RECEPTACLES
CALEFACCIÓN, LÁMPARAS SOLARES, ETC.)
• FOR INDOOR USE ONLY
• NO UTILICE PARA CONTROLAR
TOMACORRIENTES
• USE SOLAMENTE EN INTERIORES
AVERTISSEMENT
RISQUE D'INCENDIE
RISQUE DE CHOC ÉLECTRIQUE
RISQUE DE BRÛLURES
NOT FOR USE WITH MEDICAL OR
COMMANDE DES APPAREILS
ATTENTION : LIFE-SUPPORT EQUIPMENT
Z-WAVE ENABLED DEVICES SHOULD
• NE PAS DÉPASSER LES
NEVER BE USED TO SUPPLY POWER TO
CARACTÉRISTIQUES NOMINALES
OR CONTROL THE ON/OFF STATUS OF
• NE PAS UTILISER POUR COMMANDER
MEDICAL OR LIFE-SUPPORT EQUIPMENT.
DES APPAREILS POUR LESQUELS
UN FONCTIONNEMENT IMPRÉVU
POURRAIT ENTRAÎNER DES CONDITIONS
NE PAS UTILISER AVEC UN ÉQUIPEMENT
DANGEREUSES (LAMPE À RAYONS
MÉDICAL OU DE SURVIE
INFRAROUGES, LAMPE SOLAIRE, ETC.)
LES DISPOSITIFS COMPATIBLES AVEC LA
• NE PAS UTILISER POUR COMMANDER TECHNOLOGIE Z-WAVE NE DEVRAIENT
LES PRISES DE COURANT JAMAIS ÊTRE UTILISÉS POUR ALIMENTER OU
COMMANDER LA MISE EN MARCHE OU L'ARRÊT
• POUR UTILISATION INTÉRIEURE UNIQUEMENT
DE L'ÉQUIPEMENT MÉDICAL OU DE SURVIE.
SE PROHÍBE SU EMPLEO EN EQUIPO MÉDICO
O EQUIPO PARA EL MANTENIMIENTO
In-Wall
DE LAS FUNCIONES VITALES
LOS DISPOSITIVOS Z-WAVE NUNCA SE
DEBEN USAR PARA SUMINISTRAR ENERGÍA
ELÉCTRICA AL EQUIPO MÉDICO O AL EQUIPO
PARA EL MANTENIMIENTO DE FUNCIONES
VITALES, NI PARA CONTROLAR EL ESTADO DE
ENCENDIDO O APAGADO DE DICHOS EQUIPOS.
In-Wall
Insert wires into holes, do not wrap wires
Out to Light (Load)
around screws.
Do not remove screws.
B
D
E
A
C
From Breaker Box
C. LINE OR LOAD — Black (connected to power or lighting)
D. TRAVELER — Red/Other (only in 3-way installations)
E. NEUTRAL — White
Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Label wires according to the previous terminal connection.
Observe important wiring information
IMPORTANT! This switch is rated for and intended to only be used with copper wire.
Wire gauge requirements
Use 14AWG or larger wires suitable for at least 80° C for supplying line (hot), load, neutral, ground and
traveler connections.
Wire strip length:
1. For attachment using the enclosure's holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in).
2. Connect the green or bare copper ground wire to the GROUND terminal.
3. Connect the black wire from the light to either LINE/LOAD terminal.
4. Connect the black wire from the electrical service panel (hot) to the other LINE/LOAD terminal.
5. Connect the white wire to the NEUTRAL terminal (use a jumper wire if needed).
NOTE: The traveler terminal is only used for 3-way or 4-way wiring and should remain
unused if the switch is being installed in a 2-way system (one switch & one load).
6. Insert switch into the switch box being careful not to pinch or crush wires.
7. Switch must be independently mounted (vertical position only).
5. 5.
2
2
Z-WAVE INTEROPERABILITY
This product can be included and operated
in any Z-Wave network with other Z-Wave
certified devices from other manufacturers
and/or other applications. All non-battery
operated nodes within the network will
act as repeaters regardless of vendor
to increase reliability of the network.
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from the
original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and
does not extend to consequential or incidental damage to other products that may be used with this product.
This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how
long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so
the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other
rights which vary from state to state. Please contact our U.S.-based Consumer Care at 1-800-654-8483 (option 1)
between 7AM–8PM, M-F, Central Time or www.byjasco.com if the unit should prove defective within the warranty
period.
GARANTIE
Jasco Products Company garantit que ce produit est exempt de tout défaut de fabrication pour une période
de cinq ans à compter de la date de l'achat original par l'acheteur. Cette garantie se limite exclusivement à la
réparation ou au remplacement de ce produit et n'est pas applicable aux dommages indirects ou accessoires
survenus sur d'autres produits utilisés avec ce produit. Cette garantie se substitue à toute autre garantie expresse
ou implicite. Certains États ne permettent pas de restrictions quant à la durée d'une garantie implicite ou
permettent l'exclusion ou la limitation des dommages indirects et accessoires; il se peut, par conséquent, que
cette garantie ne s'applique pas dans votre cas. Cette garantie vous confère des droits juridiques précis; vous
pouvez jouir d'autres droits qui peuvent varier d'un État à l'autre. Veuillez communiquer avec notre service à
la clientèle aux États-Unis au 1-800-654-8483 (option 1) entre 7 h et 20 h (heure normale du Centre) ou par
l'intermédiaire de notre site web www.byjasco.com si l'appareil s'avère défaillant au cours de la période de
garantie.
GARANTÍA
Jasco Products Company garantiza que este producto está libre de defectos de fabricación durante un periodo
de cinco años a partir de la fecha original de compra por parte del consumidor. Esta garantía se limita a la
reparación o sustitución de este producto solamente y no se extiende a daños derivados o accidentales causados
a otros productos que se usen con esta unidad. Esa garantía remplaza a todas las demás garantías expresas o
implícitas. Algunos estados no autorizan limitaciones en cuanto a la duración de una garantía implícita ni permiten
la exclusión o limitación por daños accidentales o derivados; por lo tanto, puede que las anteriores limitaciones no
apliquen en su caso. Esta garantía le da a usted derechos específicos, y otros que usted puede tener y que varían
según el estado en el que usted reside. Si la unidad resultare defectuosa dentro del periodo de garantía, Por favor,
comuníquese con nuestro Centro de atención al cliente con sede en EE. UU. al 1-800-654-8483 (opción 1) entre 7
y 20 h, Hora del Centro, o a través de nuestro sitio de internet www.byjasco.com.
Jasco Products Company LLC, Building B
10 E. Memorial Rd. Oklahoma City, OK 73114.
SPECIFICATIONS
ADVERTENCIA
ZWA4011ENB
Power: 120VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 960W incandescent, 1/2HP motor or 1800W (15A) resistive
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
Type 1 enclosure, independently mounted (vertical position only), operating control: type 1.c action, pollution degree (2),
impulse voltage (2500V), software class A
For indoor use only
Specifications subject to change without notice due to continuing product improvement
SPÉCIFICATIONS
ZWA4011ENB
Tension : 120VCA, 60Hz
Signal (fréquence) : 908.4/916MHz
Charges maximales : 960W incandescent, moteur de 1/2HP ou résistance de 1800W (15A)
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus proche allant jusqu'à 150 pi (45.7m)
Plage de températures de fonctionnement : De 0 à 40° C (de 32 à 104° F)
Boîtier de type 1, monté indépendamment (position verticale seulement), intervention de type 1.c commande de
fonctionnement, degré de pollution (2), tension de choc de (2500 V), logiciel de classe A
Utilisation intérieure uniquement
En raison d'améliorations continues du produit, les spécifications peuvent faire l'objet de changements sans préavis
ESPECIFICACIONES
ZWA4011ENB
Energía: 120VCA, 60Hz
Señal (frecuencia): 908.4/916MHz
Cargas máximas: 960W incandescente, 1/2HP motor o 1800W (15A) resistiva
Alcance: Hasta 150 pies (45.7m) en línea de visibilidad directa entre el control inalámbrico y el módulo receptor Z-Wave
más cercano
Rango de temperatura de funcionamiento: 0-40° C (32-104° F)
Recinto de tipo 1, independientemente montado (solo en posición vertical), control de operación: acción tipo 1.c, grado de
contaminación (2), voltaje de impulso (2500V), software de clase A
Para uso en espacios interiores solamente
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto
Out to Light (Load)
B
A
D
E
C
From Breaker Box
8. Secure the switch to the box using the supplied screws.
9. Mount the wallplate.
10. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic operation
The connected light can be turned ON/OFF in two ways:
1. Manually from the front panel of the switch.
2. Remotely with a Z-Wave controller.
Manual control
The front panel rocker switch allows the user to turn ON/OFF the connected fixture.
1. To turn the connected fixture ON, press the top of the rocker.
2. To turn the connected fixture OFF, press the bottom of the rocker.
Cycle LED light
The LED below the switch acts as a guide light or status indicator.
How to cycle through options: Press up three times and down once quickly.
1. LED is ON when the load is OFF (guide light in the dark) (default).
2. LED is ON when the load is ON (indicates the switch is ON).
3. LED is always OFF.
4. LED is always ON (illuminates switch in the dark).
To change color of the paddle
2.
This step is optional. Before installation,
you may want to change the color of the
paddle to match your wallplate or décor.
1. Lift the air gap tab at the base of the paddle.
2. Push side tabs in on one side and then the other
to release paddle. Lift the cover up and off.
3. Simply put the new paddle onto the
switch by inserting the air gap and side
1.
tabs and snapping securely into place.
Once this step has been completed, please return
to section 3.
This device supports association command class (3 Groups)
• Association Group 1 supports Lifeline, Binary Switch Report
• Association Group 2 supports Basic Set and is controlled by pressing the ON or
OFF button with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing
the ON or OFF button
• Each Association Group supports 5 total nodes
The add-on switch (46199/59339) is
required for multi-switch installations.
Connecting the traveler terminal
of this switch to a standard add-on
switch will cause damage or result
in improper function. If this switch is
a part of a 3-way or 4-way multi-
switch installation, do not connect
the traveler wire or apply power
until add-on switches are correctly
installed. For more information on
3-way or 4-way installations, view
the manual or quick-start guide with
the add-on switch (46199/59339).