Publicidad
Idiomas disponibles
Idiomas disponibles
Check the device and accessory parts for transport
damage.
In case of complaints the dealer must be informed im-
mediately. Subsequent complaints will not be accept-
ed.
If possible, store the packaging until the warranty pe-
riod has expired.
Read the operating manual to make yourself familiar
with the device prior to using it.
Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
9.
Attachment / Before starting the
equipment
9.1 Fitting the wheels (7)
(enclosed accessories bag A)
• Undo the hexagon screw on the bracket (fig. 3 (1))
until the wheel axle fits into the bracket.
• Now guide the wheel axle into the bracket (fig. 3 (2))
• Fully tighten previously loosened screw.
• Now fit the wheels and washer
• Secure the wheels on the axle with a split pin
• Finally fit the small wheel cap
• Repeat this process on the other side.
9.2 Fitting the table (5)
• Undo the star-grip screw (fig. 4)
• Now fold out both side trays (11), as shown in fig. 5
• Now fit the table in the retainer intended and re-
tighten the star grip screws previously loosened
(fig. 6 (2)).
9.3 Fitting the complete control arms (10)
(enclosed accessories bag B)
The control handles on the arms point outwards!
• Insert the hexagon screw and washer through the
hole in the control arm (fig. 7 (1))
• Guide control arm (A) into the rocker switch (B)
(fig. 7 (2))
26 | GB
• Place the washer (7a) between the control arm and
tray (fig. 7 (2))
• From below, now tighten the hexagon screw with
washer and a self-locking nut
• Attention:
sufficiently that the complete control arm can be
moved to the left and right.
• Now fasten the other control arm on the other side in
accordance with the method described
9.4 Fitting the claws
(enclosed accessoriesbag C)
• Fasten the additional retainers (D) to the claws with
two Phillips head screws, washers and nuts (fig. 8)
• Make sure that the larger additional retainer is
fastened with the left claw (4).
• Place the adjustable claws on the hexagon nuts
previously attached, and fasten these with the star
grip screws and washers enclosed (fig. 8)
• Note that the prongs on the claws must point towards
each other after installation (fig. 9)
m IMPORTANT!
You must fully assemble the appliance before using it
for the first time!
10. Initial operation
Before commissioning, secure the splitter to the floor
using M10 screws, as shown in Figure 15.
Make sure the machine is completely and expertly as-
sembled. Check before every use:
• The connection cables for any defective spots
(cracks, cuts etc.).
• The machine for any possible damage.
• The firm seat of all bolts.
• The hydraulic system for leakage.
• The oil level.
Checking the oil level (fig. 13)
The hydraulic unit is a closed system with oil tank, oil
pump and control valve. Check the oil level regularly
before every use. Too low an oil level can damage the
oil pump. The oil level must be within the middle mark
on the oil dipstick. The splitting column must be retract-
ed before the check, the machine must be level. Screw
in the oil dipstick fully, to measure the oil level.
Functional test
Test the function before every use.
www.scheppach.com
Tighten
the
self-locking
nut
only
Publicidad
