EINHELL TP-AG 18/125 CE Q Li Manual De Instrucciones página 19

Important!
The equipment switches to "Standby Mode" after
10 minutes of non-use.
To reactivate: Switch on the equipment twice or
press the battery capacity indicator.
"Standby Mode" protects the battery.
Important!
Following a stoppage (due to overloading), the
cordless equipment starts up again automatically.
Important!
Wait until the machine has reached its top
speed. You can then position the angle grin-
der on the workpiece and machine it.
6.3 Speed controller (Fig. 1c/Item 6)
You can preselect the speed by turning the speed
controller (6).
The most suitable speed depends on the type of
application and the maximum rated speed of the
grinding/sanding tool. Use the speed controller
(6) to select a speed in the range from 3,000 to
10,500 min .
-1
You can choose from 5 speed settings.
These are indicated by the LEDs on the
speed display:
1 LED: 3000 min
2 LEDs: 4500 min
3 LEDs: 6500 min
4 LEDs: 8,500 min
5 LEDs: 10,500 min
Plus direction:
Minus direction:
Wait until the tool has reached its top speed.
You can then position the angle grinder on the
workpiece and machine it.
Constant electronics
This tool is equipped with constant electronics.
Constant electronics keeps the set speed
constant even when the tool is working under
load.
6.4 Overload display (Fig. 1c/Item 8)
The constant electronics function keeps the
speed constant even when the load increases. If
the load rises too high for the tool, this will be sig-
naled by fl ashing of the overload display (8).
Anl_TP_AG_18_125_CE_Q_Li_SPK13.indb 19 Anl_TP_AG_18_125_CE_Q_Li_SPK13.indb 19
GB
The following cases will be signaled by the over-
load display (8):
•
•
6.5 Battery capacity indicator (Fig. 1d/Item c)
Press the battery capacity indicator switch (e).
The battery capacity indicator (d) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
-1
The battery temperature is too low. Remove the
-1
battery from the equipment, keep it at room tem-
-1
perature for one day. If the fault reoccurs, this me-
-1
ans that the rechargeable battery has undergone
-1
exhaustive discharge and is defective. Remove
Higher speed the battery from the equipment. Never use or
Lower speed charge a defective battery.
6.6 Changing the grinding wheels (Fig. 5)
•
•
•
•
Warning!
For safety reasons the quick-clamp nut (5) may
only be used for this angle grinder.
Notice!
Only ever press the spindle lock when the
motor and grinding spindle are at a stand-
- 19 -
Exceeding the maximum power current per-
mitted for the motor. The overload display (8)
will go off again when the load is reduced or
it will flash for a short time after the tool has
been switched off in order to protect the mo-
tor from the overload.
Exceeding the maximum temperature per-
mitted for the motor. The overload display (8)
will flash for a short time and will then go off
again. Allow the tool to cool down before you
continue to use it.
The wheel is easy to change using the spind-
le lock and quick-clamp nut.
Press the spindle lock and allow the grinding
wheel to engage.
Undo the quick-clamp nut by turning it coun-
terclockwise by hand (see Fig. 5).
Change the grinding wheel or cutting wheel
and tighten the quick-clamp nut by turning it
clockwise by hand.
28.11.2022 11:33:09 28.11.2022 11:33:09