Princeton Tec REMIX Instrucciones De Operacion Y Mantenimiento

REMIX
HEADLAMP
Operating and Maintenance Instructions
ENGLISH:
Battery Installation
– See Battery Installation Diagram
• 3 AAA
• Alkaline (LR03)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment and
recommends recycling batteries. For more information
about battery recycling, please go to: www.
batteryrecycling.com
To install the batteries, unlatch the battery door. Open
the Remix case by popping the door latch over the catch
and rotate the door open. Install three AAA batteries
according to the polarity markings on the inside of the
cabinet. Observe proper battery polarity when installing
the batteries. Improper installation of the batteries will
damage the light and void the warranty.
Rotate the door to the closed position, squeeze the body
between your forefingers and thumb to snap the door
latch over the catch.
!
WARNING
• Never mix fresh and used batteries.
• Never mix different battery brands or chemistry types.
• Always remove drained batteries immediately.
• Remove batteries during long periods of storage.
NOTE: Rechargeable NiCad or NiMH batteries may result
in reduced brightness due to lower nominal voltage.
Switch Operation
– See Switch Operation diagram
The Remix has two light sources to choose from, three
5mm red LEDs or a white Maxbright LED. Each light
source has multiple modes.
To switch between light sources, press and hold the
button down until the light source switches to the desired
source. As soon as it switches release the button.
NOTE: If you keep the button pressed the light will
continue to switch back and forth between the 5mm and
Maxbright LED (on low light settings) until you release
the button.
Once you have found your desired light source, you now
can select different brightness levels. Your light will start
on "low output". To change to "a higher output" you
must press the button again in less then 1.6 seconds
from the previous press. Any additional delay will cause
the light to turn off after the next button press.
One final note about the light function – If you have the
light turned on, (and more than 1.6 seconds has passed
since your last button press) and you press and hold
the button down to switch light sources, you will be in
darkness for about one second as the light sees this
press as a signal to turn the light off and switch to the
other light source simultaneously.
**The times listed on the rear of the package assume you
have start with fresh batteries and use only one mode.
Figure 1 – Battery Replacement
1
Figure 2 – Switch Operation
®
Figure 3 – Performance
Modes
HIGH SPOT
MED SPOT
LOW SPOT
HIGH FLOOD
LOW FLOOD
DISTANCE (m)
(ANSI FL-1 Standard)
Runtime is defined as the duration of time from the initial light output value—defined as 30 seconds after the
point the device is first turned on—using fresh batteries, until the light output reaches 10% of the initial value.
Reserve time is the duration of time from 10% of initial light output value down to 0.25 lux
Troubleshooting
If the Remix fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is confirmed.
• Check the light for water contamination on the circuit
board. The light will resume normal operation once
the water is shaken or blown out and the light is
left open until completely dry. If the light has been
contaminated with salt water, flush the unit with fresh
water and dry as described above.
USA– International 5-Year Warranty
WARRANTY – Princeton Tec warrants this product to
be free from defects in workmanship and materials
under normal use for 5 years. This warranty covers all
of the component parts of the product except batteries.
This warranty does not cover deterioration due to
normal wear or damage due to misuse, alteration,
negligence, accidents, or unauthorized repair. Princeton
Tec will repair or replace parts which are defective in
workmanship or materials.
Your authorized Princeton Tec Dealer and Princeton
Tec are the only facilities authorized to repair the
product. After (3) unsuccessful attempts (within the
warranty period) to repair the product, you have the
right to elect replacement of the product or a refund
of the purchase price less allowance for use of the
product. NO INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARE INCLUDED IN THIS WARRANTY. (Some states do
not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or
exclusions may not apply to you.) This warranty gives
2
Press 1x:
Red Low
Press 2x:
Red High
Press 3x:
Off
Runtime
63h
14h
16h
6h
73h
0 9 20
3
(From red):
2 second hold:
White Low
Press 1x:
White Medium
Press 2x:
White High
(After 1.6 seconds in any mode):
Press 1x from On:
Off
Beam Pattern
25 42
you specific legal rights, and you may also have other
rights which vary from state to state.
Princeton Tec reserves the right to change product
specifications without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A (BpA) a
chemical known to the State of California to cause birth
defects or other reproductive harm.
Return Policy
If your light fails to operate, follow these simple steps:
1. Check batteries. Replace if necessary.
2. To send your light in for repair or replacement, first
contact Princeton Tec customer service on
1-800-257-9080 to request an RMA number. Please
have your light model, date of purchase and a brief
description of the fault you are experiencing. No
warranty repairs will be accepted without an RMA
number.
3. Return the light without batteries to: Princeton Tec,
PO Box 8057 Trenton NJ 08650. Postage due and
freight collect items will not be accepted.
4. Upon receipt your light will be processed in about
two weeks. Please allow additional time for return
transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2022 Princeton Tec
Reserve
22h
74h
44h
-
-
51