Oxybul FREEbul 0660939 Manual Del Usuario página 6

Keep the instructions for future reference.
NF-EN-71
Warning! Protective equipment should be worn. Not to be used in
20 kg max.: Seat mode (ride-on, walking bike)
50 kg max.: Scooter mode
Seat mode: Warning! Not to be used by children over 36 months due to the limited
strength of the seat bracket frame. The seat can only be used with this
product when the steering is completely locked by the parents using the locking button
located at the upper side of the steering assembly. Press down the locking button in
order to lock the steering of the wheels when the seat is to be mounted.
Remove the scooter and all the parts from the box. Set out all the parts
and read the assembly instructions prior to use. Keep the packaging until
assembly is complete.
General instructions
This toy must be assembled by a responsible adult. Prior to use, make sure that the
toy has been assembled properly. Remove all the parts which are not necessary for
play before giving the toy to your child. The toy should be used with caution since skill
is required to avoid falls or collisions causing injury to the user or third parties.
To use with suitable protective equipment, including a helmet, shoes, elbow, wrist and
knee protectors. Teach the child how to use it safely and responsibly.
Directions:
- The scooter can be dangerous and can cause
highways. Don't use on the public roads. It is best used on a
of gravel and grease. Avoid bumps and drainage grates that may cause an accident.
- The scooter does not include any headlights or lights. It is therefore not suited for use
at night or during periods when visibility is limited.
- Always use under adult supervision.
- Do not allow more than one child to ride the scooter at the same time.
Before and after use:
- Make sure that all locking mechanisms are securely locked:
- Check the height of the steering system, and make sure the nuts are tightened and
that the handlebars and the front wheel are perpendicular.
- The minimum height of T-bar has to be locked at the lowest position by switching the
bullet into the lowest slot. (see diagram A).
- Check all of the connection elements: the brake, the steering column's quick release
system and the wheel axles must be adjusted correctly and not damaged.
- Also check the tyre wear.
6
accidents when used on public
clean surface, free
INSTALLATION AND USE OF SEAT FOR USE ride-on / walking-bike
(see page 2)
- The modular Sporty+ scooter comes with a connector tube which is used to
There are 2 different seat heights available: 23.9 – 27.4cm from the ground. For a
comfortable ride, your child's feet should easily touch the footrest and the ground.
- Attach the seat to the connector tube by sliding it on to the tube. Select your preferred
height, then tighten the knob, using both hands to make sure the seat is securely in
place. (see diagram 1-2)
- Insert the connector tube into the integrated tube hole at the front of the scooter deck
between the two front wheels. Make sure to insert the connector tube in the correct
direction following the arrow on the connector tube (see diagram 3) and ensure the
spring ball on the side of the connector tube "clicks" into place, to securely hold the
seat frame (see diagram 3).
- Place the footrest on the deck in the correct direction. Make sure the knob is
tightened and securely (see diagram 5-6)
- Warning! Pull up the seat from the deck without pressing the side push-button on the
deck to check that the seat connector tube is safely locked in place before use.
Ride-on mode:
- Insert the handlebar tube in the back hole of the seat support frame. Align the
spring-loaded buttons with the notches at the rear of the seat and lock the handle-
bars (Figure 4). Double check that the spring-loaded button is engaged and locked
correctly.
- Adjust the height of the handle to the parent's preference (3 positions are available,
see diagram A). Loosen the quick release clamp of the T-bar handle when adjusting.
Tighten the quick release clamp to secure the T-bar handle after adjustment.
- The parent handlebar can be used to accompany children during use. Install the
footrest (see diagram 5-6). Place the child's feet on the footrest and the adult pushes
using the parent handle (T-bar).
Walking bike mode:
- Remove the handlebar tube in the back hole of the seat by pressing the 2 spring-
loaded balls.
- To remove the footrest, unscrew the knob on the footrest, then remove the footrest.
Once the footrest is removed, cover the hole in the deck with the button in-pack. (see
diagram 8-10)
- The modular Sporty+ scooter is provided with an adjustable seat which can be adapted
to the child's height (2 positions). Unscrew the knob and slide up/down to adjust the
seat height. Align the seat through the screw holes in the connector tube & retighten
the knob with both hands.
- Warning! Make sure children's feet can touch the ground freely in the seat mode
before riding.
Steering: The child pushes with his feet on the
sitting on the seat. He must proceed with caution at
the seat.
to advance, while the child's