Publicidad
Idiomas disponibles
Idiomas disponibles
4.- CLIP: indicator lamp which lights up when the input signal level is too high. In this case, decrease the
input level with the GAIN control until the indicator turns off or turns on up occasionally. If you are using
the player and this indicator lights up on channel 5/6, turn down the volume on the player itself with the
and
buttons.
5.- GAIN: input gain control. For the MIC microphone input (XLR) the range is from +20 dB to +64 dB, and
for the LINE input (6.3 mm jack) from -6 dB to +38 dB.
6.- HIGH: high pass filter with 12 KHz cut-off frequency.
7.- MID: band pass filter with a centre frequency of 2.5 KHz.
8.- LOW: low pass filter with 50 Hz cut-off frequency.
9.- MIC (5 V DC): 5 V DC condenser microphone input, 3.5 mm jack plug.
10.- FX (DSP): channel send selector to the FX(DSP) integrated effects processor.
11.- PAN/BAL: control that adjusts the stereo image in the final MAIN MIX.
- PAN: the mono input signal will be sent to the L or R channel.
- BAL: the L or R channel of the stereo input signal will be sent to the L or R channel of the MAIN MIX,
losing signal from the other channel.
12.- VOL: volume control of the input channel that is sent to the FX integrated effects processor (DSP) or to
the MAIN MIX output.
13.- LINE-LS/PLAYER: input selector for channel 5/6: LINE line input and LIVE STREAM input or player and
PC.
14.- AUX IN: direct input to the line-level MAIN MIX bus, 3.5 mm stereo jack plugs.
15.- FX (DSP) - VOL: volume control of the output of the built-in effects processor.
16.- MAIN MIX: MAIN MIX output volume slider.
17.- AUX - VOL: volume control of the AUX output signal.
- VOL: volume control of the
18.-
19.- LIVE STREAM: line input and output for smartphone/tablet connection, 3.5 mm TRRS jack connector.
The signal from the connected device will enter the mixer on channel 5/6 if the LINE-LS/PLAYER input
selector is not pressed; in addition, the connected device will receive the audio from the other inputs
of the mixer.
20.- : mixer operation indicator light.
21.-
: stereo monitor output for headphones, 3.5 mm stereo jack plug.
22.- CLIP: indicator lights on the left (L) and right (R) channels when the MAIN MIX output level is too high.
In this case, decrease the level of the input or inputs that are causing it by means of the VOL control of
the corresponding channel until the indicator light turns off or turns on occasionally.
23.- SIG: Left (L) and right (R) channel indicator lights when signal is detected at the MAIN MIX output.
24.- Integrated player controls:
a.-
/ REC: a short press starts or pauses playback. A long press starts/stops the recording of the
MAIN MIX signal on the USB device connected to the front of the unit. During recording, you can
pause/resume recording with a short press of the
b.-
/VOL-: a short press skips to the previous song. And a long press decreases the volume of the
player.
/VOL+: a short press skips to the next song. And a long press increases the volume of the player.
c.-
d.- MODE/ : a short press switches the player mode. In USB mode, a long press changes the repeat
mode: repeat all (ALL) or repeat one song (ONE).
25.- Player information display.
26.- USB port for audio file playback.
27.- FX (DSP) - PROGRAM: rotary control for effect selection. Turn the knob until the display shows
the desired effect and press the same knob to apply it. Finally, adjust the amount of effect from the
PARAMETER control and its volume with the FX (DSP) slider. This output will receive signal from the
channels that have the FX (DSP) selector pressed in. The 16 available effects are as follows:
(PHONES) monitor output.
- 3 -
button.
EN
Publicidad
