Publicidad
Idiomas disponibles
Idiomas disponibles
TOOL SPECIFICATION
Glue guns make gluing easier, cleaner and more effi cient, compared to traditional methods. Glue guns are used for cable laying,
furniture repair, wall and fl oor tile laying, and many other household tasks. Proper, reliable and safe operation of the tool depends
on appropriate use, that is why you should Read this manual before the fi rst use of the tool and keep it for future reference.
The supplier shall not be held liable for any damage resulting from failure to observe the safety regulations and recommendations
specifi ed in this manual.
ACCESSORIES
The glue gun is supplied with a detachable power cord. Glue sticks are not included with the tool.
TECHNICAL PARAMETERS
Technical data
Rated voltage
Rated frequency
Rated power
Operating temperature
Heating time
Capacity
Glue stick diameter
IEC protection class
Weight
SAFETY INSTRUCTIONS
Irresponsible use of equipment can cause fi re, therefore exercise caution when using the equipment in areas where combustible
materials are present; do not use the equipment in an explosive atmosphere; be aware that heat may be transferred to combus-
tible materials out of sight; place the equipment on its stand after use and leave it to cool down before storage; do not leave the
equipment unattended when switched on.
Before starting work, make sure that the housing and the power cord and plug are not damaged. In case of damage, do not
proceed with work. This tool must not be used by children. Children should not play with the tool. Children left unattended should
not be allowed to perform the cleaning and maintenance of the tool. This tool may be used by persons with reduced physical,
mental abilities and persons with no experience or knowledge of the tool, if supervised or instructed on its safe use so that the
risks associated with it are understood.
The tool is not designed to operate in high humidity conditions. The temperature at the place of the tool's use must be within
the range of +10
O
C ÷ +38
precipitation.
Before connecting the tool to the power supply, make sure that the voltage, frequency and performance of the power supply corre-
spond to the values shown on the tool's rating plate. The plug must fi t into the socket. It is forbidden to modify the plug or socket in
any manner to make them fi t. The tool must be connected directly to a single power supply socket. It is forbidden to use extension
cords, adapters or double sockets. The mains circuit must be equipped with a 16 A protection. Avoid contact between the power
cord and sharp edges and hot objects and surfaces. During operation, the power cord must always be fully extended and the posi-
tion of the power cord must be set so that it does not become an obstacle during operation. The power cord should not be placed in
a manner which would pose a risk of tripping. The power supply socket should be located in a place where it is always possible to
quickly remove the tool power cord plug. Always pull the power cord by the plug housing when unplugging it, never by the cord. If
the power cord or the plug is damaged, immediately disconnect it from the power supply and contact an authorised service centre
of the manufacturer for replacement. Do not use the product with a damaged power cord or plug. The power cord or plug cannot
be repaired and must be replaced with a new one that is free of defects if these components are damaged.
WARNING! The metal components of the tool can be hot during and immediately after use. Do not touch them, as it may cause
severe burns. Allow the tool components to cool down. Use gloves which protect against high temperatures if you need to move
these components before they cool down. Make sure that the fl oor near the place of use of the tool is not slippery. This will prevent
slipping, which can cause serious injuries. Never block or restrict the throughput of the ventilation openings. Never point the gun
outlet at people or animals. Do not use the tool in the bathroom or near water. Do not touch the outlet nozzle as this may cause
burns. After use, allow the tool to cool down on its own before storing. Do not, in any way, accelerate the self-cooling process of
the tool's components.
O
C, and the relative humidity must be below 70% without condensation. Do not expose the tool to
O R I G I N A L
GB
Unit
[V~]
[Hz]
[W]
[
C]
o
[min]
[g/min]
[mm]
[kg]
I N S T R U C T I O N S
YT-82403
230 - 240
50
30 (450)
100 - 200
3 - 5
20
11
II
0.35
7
Publicidad
