Switching On/Off; Working With The Chainsaw - IKRA EAS 750F Instrucciones De Manejo

tected via a residual current protective device (RCD) with
a maximum release current of 30 mA.

6.3 Switching on/off

Switching on
• Hold the chainsaw firmly with both hands on the hand-
le (thumb under the handle).
• Press and hold the switch lock (Fig.11).
• Switch the chainsaw on with the on/off switch (3). The
switch lock (14) can now be released again.
Switching off
• Release the on/off switch (3). Always pull out the
mains plug when discontinuing the work.

7. Working with the chainsaw

7.1 Preparation
Before each use, check the following to ensure safe
work:
Condition of the chainsaw
Before beginning work, inspect the chainsaw for damage
to the housing, the mains cable, the saw chain and the
guide bar. Never use an obviously damaged machine.
Oil tank
Fill level of the oil tank. Also check whether there is
sufficient oil available while working. Never operate the
saw if there is no oil or the oil level has dropped below
the minimum oil level mark in order to prevent damage
to the chain saw. On average, an oil filling is sufficient
for 10 minutes of operation, depending on the duration
of pauses and the stress.
Saw chain
Tension of the saw chain, condition of the cutters. The
sharper the saw chain is, the easier and more manage-
able the chain saw is to operate. The same applies for
the chain tension. Also check the chain tension at least
once every 10 minutes while working in order to increase
safety! New saw chains, in particular, tend to have a
higher degree of elongation.
Protective clothing
Make absolutely sure to wear the appropriate, close-
fitting protective clothing, such as chainsaw-protective
pants, gloves and safety shoes.
Hearing protection and protective goggles
Wear a safety helmet with integrated hearing protection
and a face guard. This provides protection against falling
branches and recoiling branches.
Attachment of the shoulder belt
1. Wear the shoulder belt so that it lies over the right
shoulder (Fig. 12).
2. Fasten the carabiner hook on the shaft bracket on
the shaft (Fig. 13).
Never carry the belt diagonally across your shoulders
and chest, but rather only on one shoulder, so that you
can rapidly move away from the tool in case of danger.
GB | Operating Instructions
Safe work
• In order to ensure safe work, a maximum working
• Never stand below the branch to be sawed.
• Exercise caution when sawing branches under tensi-
• Potential risk of injury from falling branches and flying
• If the machine is in operation, keep persons and ani-
• The machine is not protected against electric shock
• When working on an incline, always stand above or to
• Hold the machine as close as possible to your body.
Sawing techniques
• When removing branches, hold the machine at an an-
• Saw off the lower branches on the tree first. By do-
• At the end of the cut, the weight of the saw suddenly
• Only pull the saw out of the cut with the saw chain
• Do not saw with the tip of the guide bar.
• Do not saw into thick the branch formations. This
Sawing off smaller branches (Fig.14)
Place the stop face of the saw on the branch. This pre-
vents fitful movements of the saw at the beginning of the
cut. Applying light pressure, guide the saw through the
branch from top to bottom.
Sawing off larger and longer branches (Fig.15)
Make a relief cut when sawing larger branches.
a) First saw through 1/3 of the branch diameter from
b) Then saw from top to bottom to the first cut using the
c) Saw off longer branches in sections in order to
Kickback
The term kickback refers to when the chainsaw suddenly
jumps up and back. This is usually caused by the work-
piece coming into contact with the guide bar tip or the
clamping of the saw chain.
A kickback generates abrupt, powerful forces. Therefore,
7
angle of 60° is prescribed.
on or splintering wood.
wood projectiles!
mals away from the danger area.
when coming into contact with high-voltage lines.
Maintain a minimum clearance of 10 m from current-
carrying lines. Life-threatening danger from electric
shock!
the side of the branch to be sawed.
By doing so, you maximise your balance.
gle ranging from a maximum 60° to horizontal in order
to avoid being struck by a falling branch.
ing so, it is easier for the cut branches to fall to the
ground.
increases for the user, because the saw is no longer
supported on the branch. There is the risk of losing
control of the saw.
running. By doing so, you can prevent it from getting
jammed.
impedes the tree's ability to heal the wound.
bottom to top using the top side of the guide bar.
bottom side of the guide bar.
maintain control over the location of impact.