Crouzet IPS12 Manual De Instalación

CROUZET RANGE OF DIN RAIL INDUSTRIAL POWER SUPPLIES, from 60 to 480 W at 12 & 24 Vc. With its narrow width (from 43 to 60 mm max), they are designed
for a wide range of industrial applications. Characterised by their wide voltage input ranges (90 to 264 Va), they allow the supply of single-phase mains electric power to
DC power lines. With a high efficiency of up to 87 % @230 V, these new power supplies will fully satisfy the need of 12 & 24 Vc applications.
Please refer to the data sheet available on www.crouzet.com
IPS 12
Industrial Power Supply
• Industrial 12 Vc Power Supplies range
from 60 to 216 W
• High Efficiency, up to 87% @ 230 Va
• DIN Rail Mount
• UL & CE Certifications
MOUNTING INSTRUCTIONS
MOUNTING ON DIN RAIL
1
2
DIN rail connected to
protection wire (ground).
Refer to the derating curve. Do not exceed the load deratings. Keep ventilation
holes clear, leave enough space for cooling.
Please contact your local sales for particular application related to surrounding
space.
1.
Unit slightly rearwards, fit the unit over top hat rail.
2. Slide it downward until it hits the stop.
3.
Press against the bottom front side for locking.
Shake the unit slightly to check the locking action.
!
WARNING: Make sure input and output wire disconnected when mount
power supply onto rail.
POWER SUPPLY REMOVAL FROM DIN RAIL
Switch main power off and disconnect your system from the supply network.
Move the removal hole on the rear down edge downwards by rotating screw driver.
Gently lift lower front edge of the unit (tipping) and remove it.
DERATING CURVES
12 Vc & 24 Vc
60 W - 96 W - 120 W - 240 W - 216 W - 480 W
100
80
60
40
20
0
-25 -10 10
Ambient Temperature (°C)
For more information please go to www.crouzet.com
Industrial Power Supply
DISMOUNTING
30 50 70
°C
IPS12 & IPS24
IPS 24
PART NUMBER NOMENCLATURE
Series
IPS
IPS12
IPS12
Series
Series
IPS
IPS24
IPS24
Series
PROTECTIONS WARNING
Input Fuse
2A (60W), 3.15A (96W/120W), 4A (216W/240W), 8A (480W)
- 250 Va Internal
≥110% (60W/96W/120W), 110 140% (216W/240W/480W)
Output
Over Load
of rated output current
Protection type: Hiccup mode ; recovers automatically after fault
condition is removed
Output Hiccup mode when output is shorted ; Recovers automatically
Short Circuit after condition is removed
IPS12: 17Vc ± 1Vc (60W/96W), 16Vc ± 0.5Vc (216W),
Output
IPS24: 31.5Vc ± 1Vc (60W/120W),
Over Voltage
31.5Vc ± 0.5Vc (240W/480W)
Protection type: Latched ; Input a power has to be recycled to
recover the power supply
Over
(60W/96W/120W/480W) Power supply shuts down when the
temperature tempertarure of PCB below main transformer reaches typically
120°C ; Turns on only after the temperature falls below 90°C
typically an a power is recycled there after.
(216W/240W) Power supply shuts down when the tempertarure of
PCB below PFC main transformer reaches typically 120°C ;
Recovers automatically when temperature falls to typically 90°C.
INSTALLATION SHEET
Ref.: C.MC.SAV.00028_EN
Industrial Power Supply
• Industrial 24 Vc Power Supplies range
from 60 to 480 W
• High Efficiency, up to 87% @ 230 Va
• DIN Rail Mount
• UL & CE Certifications
Output
Power
60
Part Number
89 452 061
W: 60
89 452 061
W: 96
W: 216 89 452 061
Output
Power
60
Part Number
89 452 062
60
W:
89 452 122
120
W:
89 452 242
W: 240
89 452 242
W: 480