WERKU WK401210 Manual De Instrucciones página 4

ENG
POWER SUPPLY.
Make sure the power supply is adapted to the
►
requirements shown on the information panel of
the paint spray gun (1)
voltage will make it operate slowly
performance and may cause the motor to overheat.
EXTENSION CORD.
If the working area is at some distance from the
►
power supply, use an extension cord of enough
diameter and quality.
PREPARATION.
Do not use textured paints as they will block
►
the paint spray gun
►
the surface being painted must be prepared, and
the paint diluted until reaching the correct degree
of viscosity Make sure that the surface being
►
painted is free from dust, dirt and grease
sure that the paint being used is correctly mixed
and free from lumps and other particles
number of liquids can be sprayed using the paint
spray gun, but always check the manufacturer's
instructions on these products before using them.
PAINT VISCOSITY LEVEL.
Remember that most paints are supplied
►
ready for application using brushes or rollers,
and are not suitable for use with the paint spray
gun if they are not previously diluted
viscometer will help to decide the correct degree
of viscosity of the paint to be used (2)
the paint viscometer to the top
time the viscometer takes to empty completely
In general, the viscosity of a normal product is
►
determined by emptying times from 15 to 30 sec
In general, emptying times for the viscometer
►
for different types of material are as follows:
Plastic and latex paints:
►
Water-based paints:
►
Varnishes:
►
Oil-based paints:
►
Enamel paints:
►
Paints with aluminium:
►
Wood sealants:
►
If the paint takes an excessive amount of time to
►
empty out of the viscometer, it means it has to be
diluted further To avoid wasting paint, use small
►
amounts of the product for viscosity testing, and use
the viscometer once you have obtained the correct
degree of viscosity for the paint
some paints may contain solid particles, and will
have to be filtered before filling the cup with paint to
prevent damaging the paint spray gun.
Using the motor at low
►
This will reduce
►
To obtain a perfect finish,
►
A large
►
The
►
First, fill
►
Calculate the
►
24-28 sec
20-25 sec
20-25 sec
18-20 sec
18-22 sec
20-25 sec
28-35 sec
Remember that
►
CLEANING AND ASSEMBLING THE CUP.
Fill the paint spray gun's cup by unscrewing it from
►
its position (3)
viscosity and screw it back into the paint spray gun
Make sure that the cup is firmly screwed back
►
in place
it empties completely, to prevent the gun from
operating empty, as this may cause damage to it.
START.
Insert firmly the air hose coupling into the
►
connection at the rear of the paint spray gun and
into the base (4)
SPRAY ADJUSTMENT.
The amount of product sprayed by the paint
►
spray gun can be regulated using the fluid adjuster
(6) Before starting up the paint spray gun, make
►
Make
sure that the nozzle and its retaining nut are
firmly adjusted
with the correct viscosity that has been correctly
filtered
►
and press the switch until the paint starts to be
pulverized by the nozzle (7)
diameter using the fluid adjuster until it pulverizes
the product perfectly
the right, less product is sprayed (8)
the adjuster to the left, more product is sprayed (9).
SPRAYING TECHNIQUES.
For best results keep the paint spray gun level
►
and parallel to the surface being painted at all
times Hold the paint spray gun 25-30 cm from
►
the working surface and spray evenly from left to
right and up and down with slow movements
not spray at an angle, as this will cause the paint
to form droplets on the surface
large areas, use a correct working plan (10)
moving the arms and not the wrist
speed of the paint spray gun to achieve a smooth,
regular movement
the paint layer to be too thin
too slowly will cause the paint layer to be too thick
Apply the coats of paint one by one, leaving them
►
to dry for the times indicated by the manufacturer.
MAINTENANCE.
The paint spray gun has been designed for
►
a long working life with minimum maintenance
Optimum use depends on correct care of the
►
paint spray gun and regular cleaning
accidents, always unplug the paint spray gun from
the power source before cleaning or performing
any maintenance
cleaned effectively using compressed air after each
4
English
Fill the cup with paint of a suitable
►
Make sure that the cup is filled before
►
Press the On/Off switch (5).
►
Fill the paint cup with a product
►
Point the paint spray gun at a test section
►
By turning the adjuster to
►
Moving too quickly will cause
►
►
The paint spray gun may be
►
Change the spray
By turning
►
Do
►
When spraying
►
Spray
►
Control the
►
Similarly, moving
To prevent
►