GE JBS86SPSS Instrucciones De Instalación página 4

7
ANTI-TIP DEVICE INSTALLATION
WARNING
Tip-Over Hazard
• A child or adult can tip the range and be killed.
• Install the anti-tip bracket to the wall or floor.
• Engage the range to the anti-tip bracket by sliding the
range back such that the foot is engaged.
• Re-engage the anti-tip bracket if the range is moved.
• Failure to do so can result in death or serious burns
to children or adults.
properly, look underneath the range to see that the rear leveling leg is engaged in the bracket.
On some models, the storage drawer or kick panel can be removed for easier inspection. If
visual inspection is not possible, slide the range forward, confirm the anti-tip bracket is securely
attached to the floor or wall and slide the range back so the leveling leg is under the anti-tip
bracket. If the range is pulled from the wall for any reason, always repeat this procedure to verify
the range is properly secured by the anti-tip bracket. Never completely remove the leveling legs
or the range will not be secured to the anti-tip bracket.
8
LEVEL THE RANGE
WARNING
Never completely remove the leveling leg
as the range will not be secured to the anti-tip device properly.
MODELS WITH STORAGE DRAWER
A. Plug in unit and slide into place. Pull drawer out until it stops.
B. Lift front of drawer until the stops clear the guide. Remove the drawer.
C. Install the oven shelves in the oven and position the range where it
will be installed.
D. Check for levelness by placing a spirit level on one of the oven
shelves. Take two readings—with the level placed diagonally
first in one direction and then the other.
E. The front leveling legs can be adjusted from the bottom and
the rear legs can be adjusted from the top or the bottom.
F. Use an adjustable wrench to adjust the leveling legs until
the range is level.
G. Position cord so that it does not interfere with drawer.
Place drawer rail on guides. Push the drawer in until it stops.
H. Lift front of drawer and push in until the stops clear
the guides.
I. Lower the front of the drawer and push in until it closes.
To reduce the risk of
tipping the range, the
range must be secured by
a properly installed anti-tip
bracket. See installation
instructions shipped with
the bracket for complete
details before attempting
to install.
To check if the bracket
is installed and engaged
Stop
Spirit level
Lower
range
Leg
leveler
Raise
range
8
LEVEL THE RANGE (CONT.)
MODELS WITH WARMING DRAWERS OR DOUBLE OVEN
A. Plug in the unit.
B. Measure the height of your countertop at the rear of the opening (X).
C. Adjust two rear leveling legs so that the rear of cooktop is at the same
height as the counter (Y).
D. Slide unit into place.
E. Install oven shelves in the oven and position the range where it will be
installed.
F. Check for levelness by placing a spirit level on one of the oven shelves. Take two readings—
with the level placed diagonally first in one direction and then the other.
G. Adjust front leveling legs until the range is level.
Some models have custom handles. Please follow the instructions with the handles for
proper installation.
9
FINAL INSTALLATION CHECKLIST
Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced.
Be sure power is in service to the building.
Check that all packing materials and tape have been removed. This will include tape on metal
panel under control knobs (if applicable), adhesive tape, wire ties, cardboard and protective
plastic. Failure to remove these materials could result in damage to the appliance once the
appliance has been turned on and surfaces have heated.
Check that the door and drawer are parallel to each other and that both operate smoothly. If
they do not, see the Owner's Manual for proper replacement.
Check to make sure that the rear leveling leg is fully inserted into the Anti-Tip bracket and that
the bracket is securely installed.
If applicable - install handles following handle installation instructions and check that both ends
are secured.
OPERATION CHECKLIST
Turn on one of the surface units to observe that the element glows within 60 seconds. Turn
the unit off when glow is detected. If the glow is not detected within the time limit, recheck the
range wiring connections. If change is required, retest again. If no change is required, have
building wiring checked for proper connections and voltage.
Check that the Clock (on models so equipped) display is energized. If a series of horizontal
red lines appear in the display, disconnect power immediately. Recheck the range wiring
connections. If change is made to connections, retest again. If no change is required, have
building wiring checked for proper connections and voltage. It is recommended that the clock
be changed if the red lines appear.
Be sure all range controls are in the OFF position before leaving the range.
X
Y