Publicidad
Idiomas disponibles
Idiomas disponibles
PROGRAMMING OF THE MONOSTABLE
FUNCTION
1.
Select the channel of the receiver to be programmed
2.
Within 5 seconds, press and hold the button on the remote
control
3.
The led of the receiver goes out and goes on again: the code
has been memorised and the receiver remains standby for 5 s
with a new code to be memorised
4.
Memorise all the remote control units necessary
5.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
PROGRAMMING THE TIMER FUNCTION
1.
Select the channel of the receiver to be programmes and hold
pressed the P1 button: the LED corresponding to the selected
channel will turn on for a few seconds
2.
When the led goes off, release the P1 button.
3.
The led starts a sequence of flashings at low speed (1 flash
per second). The number of flashing corresponds to the time
which can be set as shown in the table.:
N° Flashing
Time
1
01 sec.
2
02 sec.
3
03 sec.
4
04 sec.
5
05 sec.
6
06 sec.
7
07 sec.
8
08 sec.
9
09 sec.
10
10 sec.
11
11 sec.
12
12 sec.
13
13 sec.
14
14 sec.
15
15 sec.
16
30 sec.
4.
Count the number of led flashings corresponding to the time
you wish to set
5.
Press the rx button P1 during the wished flashing: the
sequence of flashings stops and the led remains on
6.
Within 5 seconds, press and hold the button on the remote
control
7.
The led on the receiver is turned off and then comes on
again: the code has been memorised and the receiver remains
standby for 5 s with a new code to be memorised
8.
Memorise all the remote control units necessary
9.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
N° Flashing
Time
17
1 min.
18
1,5 min.
19
2 min.
20
2,5 min.
21
3 min.
22
3,5 min.
23
4 min.
24
4,5 min.
25
5 min.
26
5,5 min.
27
6 min.
28
6,5 min.
29
7 min.
30
7,5 min.
31
BISTABLE
PROGRAMMING OF THE BISTABLE FUNCTION
1.
Select the channel of the receiver to be programmes and hold
pressed the P1 button: the LED corresponding to the selected
channel will turn on for a few seconds
2.
When the led goes off, release the P1 button.
3.
The led starts a sequence of flashings at low speed (1 flash
per second). When the 30 flashings of the timer function are
over, the led remains on.
4.
Within 5 seconds, press and hold the button on the remote
control
5.
The led on the receiver is turned off and then comes on
again: the code has been memorised and the receiver remains
standby for 5 s with a new code to be memorised
6.
Memorise all the remote control units necessary
7.
After 5 seconds without a valid transmission, the led is turned
off and the receiver returns to normal operating mode
REMOTE RADIO LEARNING
This procedure allows to memorize new transmitters by radio, in
sequence and without removing the receiver from the
installation.
The transmitter which allows to enable the programming by radio
must be memorized in advance.
The keys of all the transmitters saved in the memory via radio will
have the same logic as for those of the transmitter that enabled
programming.
Therefore, if the transmitter that activated programming
has key 1 saved only, the new transmitters can only be saved
using key 1.
1.
Press for at least 5 seconds the keys 1+2 or 1+3 of one
transmitter that is already saved
2.
Release both keys
3.
Press, within 5 seconds, the key of the new transmitter that
you intend to save
4.
Release the key and repeat the procedure for the other keys
of the remote control or with other radio controls to be saved
FULL CODE ERASING
To perform a full code erasing do the following:
1.
Switch off the power supply of the receiver.
2.
By holding the key P1 of the receiver pressed, you will
reactivate the power supply.
The receiver LED goes on: release the P1 key
3.
The memory spaces are empty and available for a new
programming
- 5 -
Publicidad
