ENglIsh
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start-up can cause injury.
Removing Dust Bowl (Fig. D)
1. Remove the dust bowl
release button
3
and pulling the dust bowl down
and out.
Installing Dust Bowl (Fig. E)
NoTE: It is very important that the filter is correctly
positioned before use.
1. Line up the rib
17
on the motor housing
slot
19
of the dust bowl.
2. Install the dust bowl onto the unit and listen for an
24
audible click. Ensure the dust bowl is secured in place
2
by pressing the dust bowl
18
with the
Belt Hook (Fig. G)
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the belt hook. ONLY hang tool's belt hook
from a work belt.
WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
IMpoRTaNT: When attaching or replacing the belt hook,
use only the belt hook screw
securely tighten the screw.
The belt hook
8
can be be attached to either side of the
tool using only the screw provided, to accommodate left- or
right-handed users. If the hook is not desired at all, it can be
removed from the tool.
To move belt hook, remove the screw that holds it in place then
reassemble on the opposite side. Be sure to securely tighten
the screw.
Installing Accessories (Fig. G)
NoTE: Ensure accessories are securely in place prior to use.
•
Slide accessories onto the nozzle
•
For longer reach, attach extension
nozzle.
•
Accessories may also be attached to the end of the hose
or extension.
Extension: Reach farther to clean
overhead, under objects, and out-
of-reach places.
Flexible hose: Flexible for reaching
more hidden-away areas that the
straight extension can't reach.
Crevice nozzle: Gets in narrow
spaces around the house, jobsite,
and vehicles.
Round brush: Knocks dust and
debris out of tiny places so the
vacuum can pick it up.
gulper with removable brush:
Cleans a wider area and helps
dislodge dust and debris on larger
items around the work area.
Floor nozzle: Pair with the
extension to get dirt and debris
from the floor.
Runtime
When fully charged, the average effective usage times are
between 21 minutes with 5Ah DCB205 battery pack.
It may take several chargings before these times can
be achieved.
9
that is provided. Be sure to
10
.
11
or hose
12
to the