Publicidad
Idiomas disponibles
Idiomas disponibles
Turn off water supply before starting.
Installation must comply with all state and local laws and regulations.
1
INSTALLING FILTRATION SYSTEM
a
Personal Injury: Do not locate filter above an
outlet or other electrical device. Install head and bracket
so that connections require no stretching, kinking or
pinching of tubing.
b
From water
supply line
NOTICE
Property Damage: Tube runs need to form to the
cabinet's contours to allow storage space with no sharp
bends. Tubes need clean, perpendicular,
burr-free cuts to ensure a true fit.
c
All Hot/Cold models
Cold-only models and Hot-only
excluding HC3300
models, including HC3300
From filter or
Plug
From filter or
water supply line
water supply line
NOTICE
Property Damage: Do not extend the lines farther
than the 16" provided. Ensure tube(s) and "Y"
connnector are securely fit.
d
From water
To dispenser
supply line
It is normal for approximately 2 oz. of water
to discharge when filter is removed.
4
Screws provided are for use in wood
studs or cabinets only. Use wall anchors
(not supplied) for installation into drywall.
Separate cartridge from filter head.
Mark hole locations for filter head
and bracket in a spot that allows
for filter replacement.
Drill 1/8" starter holes and attach bracket
to wall with wood screws, turning until snug.
Insert cartridge into filter head. Top
surface of cartridge will become flush with
bottom of filter head when fully engaged.
Determine length of tubing required,
then cut to length making sure the cut
is perpendicular and burr-free.
Insert a 1/4" tube into inlet side of filter
head until it stops. Press in again to
To dispenser
ensure a secure fit.
Insert the other 1/4" tube into outlet
side of filter head until it stops. Press
in again to ensure a secure fit.
Insert the copper tubes(s) from the
dispenser into "Y" quick-connector
using the plug for hot-only models.
Connect the 1/4" tube from the right
outlet on the filter head into the quick-
connect fitting until it stops. Press in
again to ensure a secure fit.
To remove tube(s) or plug from quick-connector,
depress the release ring and gently pull away.
Connect remaining 1/4" tube to
incoming water supply line.
2
FINAL WATER CONNECTION
a
Brass Nut
Ferrule
Brass
Insert
1/4"
Plastic
Tube
NOTICE
Property Damage: Join remaining tube
to cold water supply only.
3
TURN ON WATER & CONNECT POWER
a
Scalding Hazard: The faucet dispenses near-boiling
(212ºF) water which can instantly cause scalds or burns.
Use care when operating this appliance.
4
REPLACE FILTER EVERY 6 MONTHS
a
Need QR
Code
Refer to the Performance Data Sheet online for InSinkErator Filter System
Model F-3000S. Contact an authorized InSinkErator service agent for repairs
or replacement components. Replacement filter F-3000 can be ordered by
calling 800-558-5700, visiting shop.insinkerator.com, or by contacting an
authorized InSinkErator reseller.
Certified to
NSF/ANSI/CAN 372
1-800-558-5700
Install a T-fitting (not included)
onto the cold water supply line.
Install dedicated water control valve
with 1/4" compression fitting.
At the end of the 1/4" tube
from the filter or quick-connector,
slide the supplied brass nut and
ferrule over the tube and then push
in the brass tube insert.
Insert the 1/4" tube into the 1/4"
compression fitting and tighten.
Turn on the water supply.
Depress the dispenser's HOT handle
and hold it until water flows from the
spout (approximately 1 to 2 minutes).
Flush 3 gallons (11.4 L) through filter
before first use (approximately 4
minutes).
Check all connections to ensure they
are tight and that there are no leaks.
Add the next replacement date to your calendar
(6 months from today) and write it on the enclosed
sticker and attach filter label sticker to cabinet door
or another convenient location for reference.
For your convenience and savings, scan this QR
code to sign up for our filter subscription or filter
reminder service.
Pressure: 30-80 psi (207-550 kPA)
Temperature: 33˚F - 100˚F
F-3000S Flowrate: 0.75 gpm
Capacity: 500 gallons
The F-3000 filter is certified by IAPMO R&T against
NSF/ANSI standards 42, 53, 401 and CSA B483.1 for
the reduction of claims specified in the performance
data sheet when used in system HWT300-F3000S.
HWT300-F3000S is also certified against NSF/ANSI
58 for material safety requirement and NSF/ANSI 372
for Lead Free.
262-233-2231
5
Publicidad
