Milwaukee L4 NL400 Manual Original página 8

TECHNICAL DATA
Type
Rated power output
Battery voltage
USB input
Charging time (3.0 A)
Luminous flux (3.0 A)
Mode high
Mode low
Lighting time (3.0 A)
Mode high
Mode low
Colour rendering index (CRI)
Colour temperature
Protection class
Weight
Weight with battery
Recommended ambient operating temperature
Recommended ambient charging temperature
Recommended battery types
WARNING!
Read all safety warnings and all
instructions. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS BATTERY-LAMP
Warning: Do not direct the light beam at persons or animals
and do not stare into the light beam yourself (not even from a
distance). Staring into the light beam may result in serious injury
or vision loss.
The light source of this luminaire is not replaceable; when the
light source reaches its end of life the whole luminaire shall be
replaced.
SAFETY INSTRUCTIONS BATTERY
Only use Milwaukee Type L4B... rechargeable batteries.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of eye
contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
Warning! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fluid or allow a fluid to flow inside them.
Corrosive or conductive fluids, such as seawater, certain
industrial chemicals, and bleach or bleach containing products,
etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The battery lamp can be used as lighting independently of a
mains power supply.
Do not use this product in any other way as stated for normal
use.
14
L4 NL400
Battery-Lamp
4,5 W
4,0 V
5 V DC, 0,1 A - 2,1 A
≤125 min
400 lm
250 lm
2,5 h
8 h
80
4000 K
IP 50
175,4 g
232,4 g
-18 °C ... +50 °C
+5 °C ... +40 °C
L4B...
CHARGING
1. Plug the USB cable into a power source such as an AC wall
adaptor, computer, or car port.
2. Lift the rubber cover to expose the USB Type C port.
NOTE: Always close the USB cover when light is not charging
to maintain dust and moisture protection.
3. Insert the USB Type C plug into the USB Type C port. Users
may experience longer charge times from laptops and other
power sources.
4. The indicator light ring around the power button will display
the charging status:
Red pulsing: charging, 0-49% charged
Yellow pulsing: charging, 50-99% charged
Green solid: 100% charged
Red/green flashing: too cold, wet, faulty, or no battery
Red solid: over temperature (too hot)
If the indicator light ring flashes red and green, check that the
battery is fully seated into the bay. Remove the battery and
reinsert.
If the light continues to flash red and green, the battery may be
extremely hot or cold, or wet. Allow the battery to cool down,
warm up, or dry out and then reinsert. If the problem persists,
contact a MILWAUKEE service facility.
FUEL GAUGE
The indicator light ring around the power button will display the
battery life:
Red flashing: 0-2% remaining
Red solid: 3-9% remaining
Yellow solid: 10-49% remaining
Green solid: 50-100% remaining
Overheating: If the flashlight starts to dim and the indicator light
ring is solid red, the battery may be too hot. Normal function will
resume when the battery has cooled.
ENGLISH
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Batteries which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and batteries must be kept clean.
For an optimum life-time, the batteries have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away
from moisture
Store the battery in a 30% - 50% charged condition
Every six months of storage, charge the battery as normal.
Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!)
Do not stare at the operating light source
USB Port
Class III electrical protection.
Protection class
IP50
This tool is only suitable for indoor use. Never
expose tool to rain.
Do not dispose of waste batteries, waste electrical
and electronic equipment as unsorted municipal
waste. Waste batteries and waste electrical and
electronic equipment must be collected separately.
Waste batteries, waste accumulators and light
sources have to be removed from equipment.
Check with your local authority or retailer for
recycling advice and collection point.
According to local regulations retailers may have an
obligation to take back waste batteries and Waste
electrical and electronic equipment free of charge.
Your contribution to re-use and recycling of waste
batteries and waste electrical and electronic
equipment helps to reduce the demand of raw
materials.
Waste batteries, in particular containing lithium and
waste Electrical and electronic equipment contain
valuable, recyclable materials, which can adversely
impact the environment and the human health, if
not disposed of in an environmentally compatible
manner.
Delete personal data from waste equipment, if any.
European Conformity Mark
UK Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 15