Auta 701905 Manual Del Usuario página 5

INTERNAL INTERCOM TELEPHONE WITH KEYBOARD AND DISPLAY
Settings:
- "General Call" Configuration (J1).
To receive a "General Call" the J1 jumper must be set in 2-3 position. If J1 jumper does not exist or it is set in position 1-2, the
o
"General Call" will be ignored.
- "Only Receive" Configuration (SWITCH7).
If the SWITCH7 of the configuration dip-switch is activated (down), this TELEPHONE can ONLY receive calls. It will not be possible
o
to initiate a call from this TELEPHONE.
- "Priority" Configuration (SWITCH8).
If the SWITCH8 of the configuration dip-switch is activated (down), this TELEPHONE will end any current conversation, setting the
o
line free to perform any new call.
- MULTITONE Configuration (Up to 7 different melodies).
Pressing C with the TELEPHONE hung up; we can select the desired ringtone.
o
- RINGTONES VOLUME Configuration (2 levels).
Pressing B we can select the ringtones volume.
o
- Setting The NUMBER OF RINGTONES and the ELECTRONIC CALL EXTENSION (0 to 4 ringtones)
See Table 1.
o
- Setting AUXILIARY OUTPUT (1 second pulse or TOGGLE)
See Table 1.
o
Features:
- Handset with keyboard or with keyboard-display.
- KEYBOARD dialing.
- UP TO 63 TELEPHONE maximum.
- EVERY TELEPHONE CODIFY WITH ID=0, will always make a "General Call" with just one touch of the (KEY button) + pick the handset up.
- CONVERSATION LENGTH: Minimum 90s. From here, the conversation can continue indefinitely, unless a third party wants to use the
line, which will cause both devices return to its standby mode. This is indicated by a short tone in the speaker and a "+" in the display during
the conversation.
- CALLS CANNOT BE RECEIVED if the handset is picked up.
- In case the handset has display, pressing C+OK+1+OK will give us access to the internal settings menu:
X: TELEPHONE address (from 1 to 63).
o
B: "1" means the "General Call" is enabled. Otherwise it will be "0".
o
R: "1" means the "Only Receive Mode" is enabled. Otherwise it will be "0".
o
P: "1" means that this is a "Priority Telephone". Otherwise it will be "0".
o
Functioning:
STANDBY:
·
Handset hung up, blue led ON and keyboard leds OFF.
o
· Make a call:
Pick up the handset (the blue led will start flashing and the display will turn on), enter the TELEPHONE number we want to
o
call and then press OK.(i.e., Call nº3)
§ Pick up the handset, press nº 3 and then OK. If the TELEPHONE nº3 exists, the green led will start flashing, the
display will show a progress bar and the TELEPHONE will start ringing. Otherwise, the led will turn off and the
display will only show a BELL symbol.
§
When trying to call to codes greater than 63 or if the line is busy, we will see two red flashes and the system will
return to its standby mode.
General Call. With the handset hung up, keep the KEY button pressed for 2s. The blue and green leds will blink quickly and
o
when lifting the handset up, a call will be made to all the TELEPHONES that have the "General Call" enabled. The display will
show the symbol "*" that will turn into the number of the first TELEPHONE that picks up.
If we have already pressed the KEY button during 2 seconds and we want to return to the standby mode without performing
o
a call, we can press the AUX1 button, or pick up and hang up quickly, or just wait 30s. The blue led should return to its
original blue light.
Receive a call:
·
While the handset is hung up, the TELEPHONE can receive calls. It will start ringing for up to 30s and the blue led will flash
o
quickly. We may terminate the call pressing the AUX1 button, or just lift the handset up to start the conversation. At this
point, the blue led will flash slower and we will have audio at least for 90s (see "CONVERSATION LENGTH" in features).
TELEFONO INTERCOM CON TECLADO / DISPLAY
FUNCTIONING