Stanley PPRH5KL Manual De Instrucciones página 6

Fuente de energía profesional

página de 12

/ 12
Marcadores

Idiomas disponibles

area LigHt

The built-in 3-LED area light located on the back of the unit is controlled by the area light on/off button on the front panel (refer to

the Features section to locate). Press the area light on/off button once to turn the light on. Press the area light on/off button again

to turn the area light off. Make sure the area light and the unit are turned off when the unit is being recharged or stored.

Periodically check the unit' s battery status by pressing the battery power level button. (Two red and one green battery status

indicator lights indicate a full battery. Only one red battery status indicator lights indicates that the unit needs to be recharged.)

POrtaBLe COMPressOr

The built-in 12 volt DC compressor is the ultimate compressor for all vehicle tires, trailer tires and recreational inflatables. The

compressor hose with connector (chuck) is stored in the compressor hose storage conpartment. The compressor on/off switch is

located on the front panel of the unit to the right of the air pressure gage (refer to the Features section to locate). The compressor

can operate long enough to fill up to 3 average sized tires before the battery must be recharged.

The compressor may be used by removing the air hose from the storage compartment and, if required, fitting an appropriate nozzle

to the air hose. Return hose to the storage compartment after use.

WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: FOLLOW ALL SAFETY INSTRUCTIONS FOUND

IN THE "SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS" SECTION OF THIS INSTRUCTION MANUAL.

CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:

Do not operate compressor continuously for extended periods of time (approximately 10 minutes, depending on ambient

temperatures), as it may overheat. In such event, compressor will automatically shut down. Immediately press the compressor on/

off button to turn the compressor off. Restart after a cooling down period of approximately 30 minutes.

inflating tires or Products with valve stems

1. Place connector (chuck) on valve stem.

2. Ensure connector is pushed on to valve stem as far as possible before closing thumb latch.

3. Make sure latch is secure.

4. Turn on the compressor power switch.

5. Check pressure with the pressure gage.

6. When desired pressure is reached, open thumb latch and remove connector from valve stem.

7. Turn off compressor power switch.

8. Allow unit to cool before storing away.

9. Store compressor hose and connector (chuck) in storage compartment.

inflating Other inflatables without valve stems

Inflation of other items requires use of one of the adapters (nozzles).

1. Select the appropriate nozzle, located on the inside back cover.

2. Insert appropriate adapter (i.e. needle) into connector (chuck) and close thumb latch.

3. Insert adapter (i.e., needle) into item to inflate to appropriate pressure.

4. Turn on the compressor power switch — inflate to desired pressure or fullness.

IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.

5. Remove adapter.

6. Switch the Compressor Power Switch off.

7. Allow unit to cool before storing away.

8. Store compressor hose and connector (chuck) in storage compartment.

Care aND MaiNteNaNCe

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we

recommend that the battery is charged at least every 30 days.

Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened with a mild

solution of water and detergent.

There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to

replace any components that have become worn or broken.

Battery replacement/disposal

BATTERY REPLACEMENT

The battery should last the service life of the unit. Service life is dependent on a number of factors including but not limited to

the number of recharge cycles, and proper care and maintenance of the battery by the end user. Contact manufacturer for any

information you may need.

PPRH5KL_ManualENSP_050813.indd 10-11

SAFE BATTERY DISPOSAL

Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is

required, contact your local authority for information. Failure to comply with local, state and federal regulations can

result in fines, or imprisonment.

Contact your local waste management authority to dispose of this product.

WARNINGS:

• Do not dispose of the battery in fire as this may result in an explosion.

• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result

in injury or fire).

• Do not expose battery to fire or intense heat as it may explode.

12 volt DC charger plug fuse replacement (may be sold separately)

The fuse in the plug end of the 12 volt DC charger protects the adapter' s charging circuit. If the 120 volt AC charger operates, but the DC

charging adapter does not, then this fuse may be opened (blown).

To replace the fuse:

1. Unscrew the end cap of the DC plug (counterclockwise).

2. Remove spring center contact and fuse.

3. Check fuse with a continuity checker.

4. If blown, locate a replacement 8 amp volt fuse.

5. Replace the fuse, spring, contact and end cap.

6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.

7. Test for proper operation of the 12 Volt DC Charging Adapter.

trOuBLesHOOtiNg

Unit will not charge

• Make sure the inverter power switch is in the off position.

• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning AC outlet.

• Make sure the 12 volt DC charger is properly connected to both the unit and a functioning DC power source.

Unit fails to jump-start

• Make sure unit' s jump-starter power switch is in the on position.