Beamz BFP120 Manual De Instrucciones página 2

Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the unit in order to benefit
fully from all features.
Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire
and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for
future reference.
- Prior to using the unit, please ask advice from a specialist.
When the unit is switched on for the first time, some smell
may occur. This is normal and will disappear after a while.
- The unit contains voltage carrying parts. Therefore do NOT
open the housing.
- Do not place metal objects or pour liquids into the unit This
may cause electrical shock and malfunction.
- Do not place the unit near heat sources such as radiators,
etc. Do not place the unit on a vibrating surface. Do not
cover the ventilation holes.
- The unit is not suitable for continuous use.
- Be careful with the mains lead and do not damage it. A
faulty or damaged mains lead can cause electrical shock
and malfunction.
- When unplugging the unit from a mains outlet, always pull
the plug, never the lead.
- Do not plug or unplug the unit with wet hands.
- If the plug and/or the mains lead are damaged, they need to
be replaced by a qualified technician.
- If the unit is damaged to such an extent that internal parts
are visible, do NOT plug the unit into a mains outlet and DO
NOT switch the unit on. Contact your dealer. Do NOT
connect the unit to a rheostat or dimmer.
- To avoid fire and shock hazard, do not expose the unit to
rain and moisture.
- All repairs should be carried out by a qualified technician
only.
- Connect the unit to an earthed mains outlet (220-
240Vac/50Hz) protected by a 10-16A fuse.
- During a thunderstorm or if the unit will not be used for a
longer period of time, unplug it from the mains. The rule is:
Unplug it from the mains when not in use.
- If the unit has not been used for a longer period of time,
condensation may occur. Let the unit reach room
temperature before you switch it on. Never use the unit in
humid rooms or outdoors.
- During operation, the housing becomes very hot. Do not
touch it during operation and immediately after.
This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient
magnitude to cause a shock hazard.
This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read
and adhere to.
DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks
should be aware of the effects that this light effect may have on them.
The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and their
guarantee!
NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and
35°C/95°F.
Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your
dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other.
Specifications can be changed without prior notice.
Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the unit. This would also invalid
your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings
contained in this manual. Beamz cannot be held responsible for personal injuries caused by a disrespect of the safety recommendations
and warnings. This is also applicable to all damages in whatever form.
2
ENGLISH
- To prevent accidents in companies, you must follow the
applicable guide lines and follow the instructions.
- Secure the unit with an extra safety chain if the unit is ceiling
mount. Use a truss system with clamps. Make sure nobody
stands in the mounting area. Mount the effect at least 50cm
away from inflammable material and leave at least 1 meter
space on every side to ensure sufficient cooling.
- This unit contains high intensity LEDs. Do not look into the
LED light to prevent damage to your eyes.
- Do not repeatedly switch the fixture on and off. This
shortens the life time.
- Keep the unit out of the reach of children. Do not leave the
unit unattended.
- Do not use cleaning sprays to clean switches. The residues
of these sprays cause deposits of dust and grease. In case
of malfunction, always seek advice from a specialist.
- Only operate the unit with clean hands.
- Do not force the controls.
- If the unit has fallen, always have it checked by a qualified
technician before you switch the unit on again.
- Do not use chemicals to clean the unit. They damage the
varnish. Only clean the unit with a dry cloth.
- Keep away from electronic equipment that may cause
interference.
- Only use original spares for repairs, otherwise serious
damage and/or dangerous radiation may occur.
- Switch the unit off prior to unplugging it from the mains
and/or other equipment. Unplug all leads and cables prior to
moving the unit.
- Make sure that the mains lead cannot be damaged when
people walk on it. Check the mains lead before every use for
damages and faults!
- The mains voltage is 220-240Vac/50Hz. Check if power
outlet match. If you travel, make sure that the mains voltage
of the country is suitable for this unit.
- Keep the original packing material so that you can transport
the unit in safe conditions