Publicidad
Idiomas disponibles
Idiomas disponibles
•
Do not touch the hot surface of the ceramic field. Please note: the induction hotplate does not heat up itself during
cooking, but the temperature of the cookware heats up the hotplate!
•
Do not heat up any unopened tins on the induction hotplate. A heated tin could explode; therefore remove the lid
under all circumstances beforehand.
•
Scientific tests have proven that induction hotplates do not pose a risk. However, persons with a pacemaker should
keep a minimum distance of 60 cm to the device while it is in operation.
Operating the device
•
Plug the power plug into a suitable outlet.
•
The control lamp of the ON/STANDBY switch lights up and the temperature of the cooker plate surface displayed: if
the temperature of the surface of the induction cooker lower than 50°C,the display shows"-L-".When the temperature
of the cooker plate surface is over 50°C ,the display shows "-H-" . An acoustic signal sounds. Now the device is in
standby mode.
•
Place suitable cookware in the centre of the hotplate.
•
Now press the ON/STANDBY switch once to turn the induction hotplate on. T he control lamps of "HEAT" blinks and
an acoustic signal sounds. (NOTE: if there is no further operation within 30 seconds after pressing ON/STANDBY key,
the ON/STANDBY control lamp turns off and an acoustic signal sounds, the unit goes back to standby mode. Press
ON/STANDBY again or any other key to restart the device).
•
Press the function key HEAT noce, the preset power stage "5" is selected and the device turns on.
•
With the + / - keys, you can change the settings at any time in a range from 1 – 9.
•
You can also change to the power stage selection or the temperature stage selection there without changing the
preset time.
•
Once the cooking or warming process is finished, disconnect the mains plug from the out- l et!
•
Do not place any empty cookware on the ceramic field. Heating an empty pot or pan activates the overheating
protection and the device turns off.
•
Do not operate the device if it is damaged in any way or does not function properly.
•
The use of accessories and spare parts not recommended by the manufacturer may lead to damage on the device
and injuries.
Cleaning and maintenance
•
Pull the power plug prior to cleaning the device. Do not use any caustic cleaning agents and make sure that no water
penetrates the device.
•
To protect yourself from electric shock, never immerse the device, its cables and the plug in water or other liquids.
•
Wipe off the ceramic field with a damp cloth or use a mild, non-abrasive soap solution.
•
Wipe off the casing and the operating panel with a soft cloth or a mild detergent.
•
Do not use any petrol products to not damage the plastic parts and the casing/operating panel.
•
Do not use any flammable, acidy or alkaline materials or substances near the device, as this may reduce the service
life of the device and lead to deflagration when the device is turned on.
•
Make sure that the bottom of the cookware does not scrape across the surface of the ceramic field, although a
scratched surface does not impair the use of the device.
•
Make sure that the device was properly cleaned before storing it in a dry place.
DETAILS OF CODE NO. AS FOLLOW:
E01: Electronic control of low voltage. (<160V)
Self-help: Make sure the appliance is connected to the voltage indicated on the rating label.
E02: Electronic control of excess voltage (>270V)
Self-help: Make sure the appliance is connected to the voltage indicated on the rating label.
E03: IGBT open or short circuit.
Self-help: Please send back to customer service.
E05: Overheating protection on power mode (>150°C)
Self-help: Eliminate the course of overheating. Once the cooktop has cooled, the appliance can be put into operation
again.
E06: Temperature sensor open or short circuit
Self-help: The temperature sensor underneath the glass ceramic plate is defective. Please send back to customer serivce.
3
Publicidad
