Descargar Imprimir esta página

Matco Tools AL23 Instrucciones De Operación página 3

Publicidad

Idiomas disponibles

Idiomas disponibles

insTALLATion of fiLTer/reguLATor
1. Maximum air pressure to unit is 140 PSIG (9.7 BAR).
2. Mount the unit as close to the item to be protected as possible.
3. Direction of air flow is designated by an " " and " " on the
primary unit.
4. Position the water discharge valve (#12) with the " " pointing
upward.
5. Proper water drainage should be allowed beneath the water
discharge valve (#12). Provide a container to catch the water
drainage or attach a rubber hose to channel the water away from
walk area to avoid creating a hazardous walking area.
6. Install Dial Gauge (#17) by screwing brass fitting on back of
Gauge clockwise into the threaded hole provided in front of the
primary unit, just above the regulator adjustment knob (#26).
reguLATion of Air pressure
1. Unlock adjusting knob (#26) by pulling down gently, then turn
the knob clockwise to increase air pressure and counterclockwise
to decrease air pressure.
2. After setting the desired air pressure, push up on the
adjustment knob (#26) until the knob clicks back into the lock
position. At this point, the adjustment knob should not turn in
either direction.
3. Do not exceed any pressure rating of any component in the
system.
drAinAge
1. Note that when there is no air pressure supplied to the unit,
any water in the unit will automatically discharge.
2. When air pressure is supplied to the unit, water may be
discharged by turning the water discharge valve (#12) until the
" " is pointed down. NOTE: When the water level exceeds the
maximum level as noted on the shatterguard. (#3), drain the water
so that optimal dehumidification can be maintained.
MAinTenAnce
1. Before performing any maintenance on this unit, shut off the
air supply to the unit and completely discharge all air until no air
pressure exists in the unit. Avoid breathing any discharged air
directly.
WARNING: A PRESSURIZED STREAM OF AIR
CAN CAUSE SERIOUS INJURY!
2. Unscrew shatterguard (#3) counterclockwise and remove.
Then, unscrew the bowl baffle (#6) counterclockwise and remove,
being careful not to lose the intercepter (#8). The filter (#7) may
then be removed and rinsed of any debris. The filter may be
reinstalled for repeated use.
3. Clean the transparent bowl (#2) with a clean, dry cloth. Do not
use any chemical that might damage the bowl material. Upon
AL23
AL23 FILTER AND REGULATOR UNIT
reassembly, be sure bowl baffle (#6) and shatterguard (#3) are
securely tightened.
WARNING!
Pressure systems can leak causing flying particles.
Wear safety goggles. (User and bystanders).
Read and follow instructions.
Flying particles can cause injury.
Compressor systems contain air under pressure that can create
a high pressure stream.
Relieve pressure before servicing.
A pressurized air stream can cause injury.
WARNING: THIS UNIT IS NOT TO BE USED WITH ANY
OTHER FLUIDS, ESPECIALLY FLAMMABLE LIQUIDS SUCH AS
GASOLINE OR ALCOHOL. SERIOUS DAMAGE OR INJURY TO THE
USER COULD RESULT.
WArrAnTy
Matco® air tool accessories are warranted against defects in
materials or workmanship for a period of 1 year from original
purchase. We will repair or replace at our option any defective part
or unit which proves to be defective in material or workmanship
within this warranty plan. This warranty does not cover damage
to accessories arising from alteration, abuse or misuse, and does
not cover any repairs or replacement made by anyone other than
Matco or its authorized service centers.
The foregoing obligation is Matco Tools sole liability under this
or any implied warranty and under no circumstances shall we be
liable for any incidental or consequential damages.
NOTE: Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Return air tool accessories to Matco Tools transportation prepaid.
Be certain to include your name and address, evidence of the
purchase date, and description of the suspected defect.
If you have any questions about warranty service, please write
to Matco Tools, Stow, OH 44224. This warranty gives you specific
legal rights and you may also have other rights which vary from
state to state.
3
05/15/12

Publicidad

loading