Publicidad
NOTICE
THIS ARTICLE MEETS OR EXCEEDS
ALL REQUIREMENTS COVERED IN
ASTM F833 STANDARD AND LATEST
REVISIONS.
The images referring to the textile details may
differ from the collection purchased.
For more information, consult our website:
www.pegperego.com
INSTRUCTIONS
1 OPENING: Before opening the frame, remove
(without using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER
BEYOND ITS LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY
HANDLE OR TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES
TO THIS FEATURE.
Press down the side fastener, hold the upper
section of the handle and rotate it towards
you until the frame is fully opened (fig_a).
Open frame (fig_b).
The frame is properly opened when the
attachment on the base clicks into place, as
shown.
2 FITTING THE WHEELS: Slot the uprights into
the rear wheel crosspiece (fig_a), ensuring
that it is facing the right way, then push the
rear wheels on and make sure that they click
into place (fig_b). To mount the front wheels,
fit them into the uprights until they lock into
place (fig_c).
3 ATTACHING THE MAIN HANDLE: if the handle
tube faces upwards, align it with the stroller
(Fig_a).
Fasten the handle to the frame as shown in
the figure (Fig_b).
To complete the operation, press the two
side buttons on the handle (Fig_c) to ensure
the handle pushes in all the way, until it clicks
into place (Fig_d).
4 FITTING THE BASKET: if lowered, lift the
basket tube to the horizontal position. Press
the silver buttons under the metal basket
tube located at the back of the stroller (fig_a)
and remove the metal tube (fig_b). Thread
the tube through the fabric loop on the
back of the basket, making sure that the two
silver buttons are facing downward (fig_c).
Re-attach the tube to the housings (fig_d).
5 Secure the two upper basket vinyl eyelets to
the two grey buttons on either side of the
metal tube housing. Please note that the
eyelets open (fig_e).
IMPORTANT! Fasten the three lower basket
loops to the three grey buttons on the rear
bar fig_f).
WARNING! If this operation is not completed
properly, the basket will not support any weight.
Fasten the front basket flaps to the grey
buttons on the frame (fig_g) and then secure
the basket centrally to the footrest using the
Velcro strap (fig_h).
6 HOOD: Fasten the hood at the back using
the Velcro strip (fig_a), insert the hood
attachments into their slots (fig_b), secure
with the external rubber band to the buttons
on the inside of the handlebar (fig_c), and
finally button the hood laterally to the frame
(fig_d).
7 FIXED OR SWIVELING FRONT WHEELS: Lift the
levers to prevent the wheels from swiveling
(fig_a) and lower them to allow the wheels to
swivel (fig_b). On uneven surfaces, the wheels
should be set to their fixed position.
8 BRAKE: Press the lever down to apply the
brake on the chassis and lift it to release the
brake.
9 ADJUSTABLE HANDLEBAR: To adjust the
height of the handlebar, press both of the
side buttons at the same time (fig_a) and
swing it into the desired position (fig_b), then
release the buttons.
10 FOOTREST: before adjusting the foot rest,
ensure its cover is accurately fitted; if it isn't,
fit it accordingly. To lower the footrest push
the two levers downwards and then push
the footrest downwards (fig_a); to raise the
footrest lift it upwards (fig_b).
11 FRONT BAR: insert the front bar as per the
sequence shown in the figure.
12 It can be adjusted into 2 positions:
POSITION 1: to use
POSITION 2: to attach the car seat
13 To remove the front bar, press down on the
buttons from both sides, as per the sequence
shown and remove (fig_a).
It is possible to open the front bar on one
side only, so as to facilitate the child's entry
and exit (fig_b).
WARNING: The front bar has not been
designed to support the child's weight; the
front bar has not been designed to lift the
seat with the child's weight. The front bar
does not replace the seat belt.
14 Before releasing the armrest, unfasten the
elastic from the cover on both sides.
15 Slightly close the chassis.
Rotate the armrest to unfasten it from the
cap, as shown in figure (fig.a).
To completely remove the armrest, pull it
outwards on both sides (fig.b).
Finally reattach the cover elastics to the
chassis.
16 Chassis without armrests. Keep the armrests
for a future use.
17 To reattach the armrests, proceed in reverse
sense. Pay attention to the attachment
direction.
- 15 -
Publicidad
