Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Model VINV300 Ventilator Kit
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer or your distribu-
tor.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a
qualified person(s) in accordance with all applicable codes
and standards, including fire-rated construction codes and
standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equip-
ment to prevent backdrafting. Follow the heating equipment
manufacturer's guidelines and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code authori-
ties.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Do not use this unit with an additional speed control device.
8. To reduce the risk of fire, use only steel ductwork.
9. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2. Always turn hood ON when cooking at high heat or when
cooking flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed
to accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the
size of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or
metal tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN - You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels -
violent steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you
already know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
CAUTION
1. For general ventilating use only. Do not use to exhaust haz-
ardous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbal-
anced impellers, keep drywall spray, construction dust, etc.
off power unit.
3. Your ventilator motor has a thermal overload which will au-
tomatically shut off the motor if it becomes overheated. The
motor will restart when it cools down. If the motor continues
to shut off and restart, have the hood serviced.
4. Please read specification label on product for further infor-
mation and requirements.
FOR USE ONLY WITH
VIKING HOOD MODELS *
VCWH, VWH, VBCV
* Contact your local Viking dealer for specific
Blower Dimensions
9.50 x 8.50 x 8.50
MOUNTING PLATE CONFIGURATIONS:
020971-000
USE ON VCWH 30" THRU 36" HOODS
020972-000
USE ON VWH AND VBCV 30" THRU 36"
HOODS
050722-000
USE ON VBCV53638 HOODS
1
!
compatibility information.

Publicidad

loading

Resumen de contenidos para Viking VINV300

  • Página 1 Follow the heating equipment VCWH, VWH, VBCV manufacturer’s guidelines and safety standards such as those * Contact your local Viking dealer for specific published by the National Fire Protection Association (NFPA), compatibility information. and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authori- ties.
  • Página 2 Model VINV300 Ventilator Kit VENTILATOR KIT INSTALLATION Attach the GUARD with (3) M4 x 0.7 screws provided. 2. Choose the correct VENTILATOR MOUNTING PLATE for your hood series. (VBCV53638 will only be shipped with the 050722-000 mounting plate.) 3. Attach DAMPER to ventilator mounting plate, as shown. Use three (3) HEX SCREWS. Note: Damper FLANGE to be captured by screw heads.
  • Página 3 Ensemble de ventilateur modèle VINV300 AVERTISSEMENT AVERTISSEMENT A F I N D E D I M I N U E R L E S R I S Q U E S D ’ I N C E N D I E , 4.
  • Página 4 Ensemble de ventilateur modèle VINV300 INSTALLATION DE L’ENSEMBLE DE VENTILATEUR 1. Fixez le GARDE avec (3) M4 x 0,7 vis fournies. 2. Choisissez la PLAQUE DE MONTAGE de ventilateur convenant à la série de votre hotte. (VBCV53638 seront unique- ment expédiés avec les 050722-000 plaque de montage.) 3.
  • Página 5 Asociación Nacional de Protección contra Incendios (National Fire * Comuníquese con el distribuidor Viking de su Protection Association, NFPA), y la Sociedad Americana de Ingenieros localidad si desea información específica de en Calefacción, Refrigeración y Aire Acondicionado (American Society...
  • Página 6 Juego de ventilador modelo VINV300 INSTALACIÓN DEL JUEGO DEL VENTILADOR 1. Coloque la GUARDIA con (3) M4 x 0,7 tornillos suministrados. 2. Elija la PLACA DE MONTAJE de ventilador correcta para la serie de su campana. (VBCV53638 sólo serán enviados con la 050722-000 placa de montaje.
  • Página 7 FOGÃO: VCWH, VWH, VBCV 1. Nunca deixe sem supervisão as unidades de superfície quan- * Contate o seu revendedor Viking local para obter do estiverem em fogo alto. Transbordamentos podem causar informações de compatibilidade específicas. fumaça e derramamentos gordurosos que podem incendiar.
  • Página 8 Kit de ventilador modelo VINV300 INSTALAÇÃO DO KIT DO VENTILADOR Coloque a PROTEÇÃO com (3) parafusos M4 x 0,7 fornecidos. 2. Escolha a PLACA DE MONTAGEM DO VENTILADOR correta para a série da sua coifa. (VBCV53638 só serão enviados com o 050722-000 placa de montagem.) 3.