Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING INSTRUCTIONS
Installing LP Gas Tank
To operate, you will need one precision-filled
standard grill LP gas tank with external valve threads.
CAUTION: LP gas tank must be
properly disconnected and removed
prior to moving this outdoor fireplace.
Inserting LP Gas Tank
WARNING: Make sure LP gas tank valve is closed.
1. Loosen LP gas tank retainer bolt by turning counter-clockwise.
2. Place precision-filled LP gas tank upright into hole in outdoor fireplace
base so the tank valve is facing the gas line connection.
3. Secure tank by turning LP gas tank retainer bolt clockwise until tight.
Step 1
Connecting LP Gas Tank
1. Before connecting be sure there is no debris caught
head of the LP gas tank head of the regulator
in the
valve or in the head of the burner or burner ports.
2. Connect regulator/hose assembly to tank by turning
knob clockwise until it stops.
Disconnecting LP Gas Tank
1. Before disconnecting make sure the LP gas tank
valve is "CLOSED".
2. Disconnect regulator/hose assembly from LP gas
tank by
turning knob counterclockwise until it
CAUTION: LP gas tank must be
properly
disconnected and removed
prior to moving this fire table.
3. Place the protective cap cover on the LP tank and store the
tank outdoors in a well ventilated area out of direct sunlight.
20 lb
9 Kg
12.2 in. / 31 cm
.
is loose.
.
Operating Instructions
Checking for Leaks
WARNING:
Before using this outdoor
fireplace, make sure you have read,
understand and are following
all information provided in the
"Important Safety Information" section
on page 2. Failure to follow those
instructions can
cause death,
injury or property
damage.
Burner Connections
1. Make sure the regulator hose and valve connections are securely
fastened to the burner and the tank.
2. Visually check the connection between the burner/venturi
tube and orifice.
3. Make sure the burner/venturi tube fits over the orifice.
WARNING:
Failure to inspect this
connection
or follow these
cause
a fire or
an explosion which can cause
death, serious bodily injury or damage to property.
4 .
Please refer to diagram for proper installation
Figures 1 and 2).
5. If the burner/venturi tube does not rest flush to the
orifice, as shown, please contact
assistance.
Tank/Gas Line Connection
1. Make 2-3 oz . of leak detection solution by
mixing one part liquid dishwashing soap with
three parts water.
2. Make sure control knobs are in the
"
OFF" position (Figure 3).
3. Connect LP gas tank per "Installing LP Gas
Tank''
4. Turn off the igniter cover and put the battery (10) inside according to the electrode (Figure 4
5. Close the firepit door panel (Figure 5).
6. Turn LP gas tank valve to "OPEN ".
7. Spoon several drops of solution or use a squirt
bottle, at all "X" locations (Figures 1 and 2).
a. If any bubbles appear, turn LP gas tank valve to
"CLOSED", reconnect and re-test.
b. If you continue to see bubbles after several attempts
turn LP gas tank valve to "CLOSED" and
disconnect LP gas tank, per
"Disconnecting LP Gas Tank".
Contact 1-800-643-0067 for assistance.
c. If no bubbles appear after one minute, turn LP gas
tank valve to "CLOSED", wipe away solution
proceed.
Lighting
WARNING: NEVER light the burner
with the cover on the outdoor
fireplace.
CAUTION: Keep outdoor gas
appliance area clear and free from
combustible materials, gasoline and
other flammable vapors and liquids.
CAUTION: Do NOT obstruct the
flow of
combustion and ventilation air.
CAUTION : Check and clean burner/venturi tubes for insects and insect
nests. A clogged tube can lead to a fire.
1. Make sure all labels, packaging and protective films have been removed from
the outdoor fireplace.
2. Check for obstructions of airflow to the burner. Spiders, insects and webs can
clog the burner/venturi tube. A clogged burner tube can lead to a fire.
3. Control knob must be in the "
4. Clear small area of glass rocks away from the igniter cover (Figure 6).
5. Connect LP gas tank per "Installing LP Gas Tank" section.
6. Turn LP gas tank valve to "OPEN".
7. Push and hold the electronic igniter to create sparks within the electrode,
continue to hold.
8. Push in the control knob and turn to the "ON" position, Keep holding down the
control knob to allow gas to flow for 20 seconds.
9. After 20 seconds, release and turn control knob counterclockwise to adjust flame
to desired height.
10. If ignition does not occur in 20 seconds turn burner control knob to " OFF" wait
5 minutes, fan with a newspaper or magazine, and repeat lighting procedure.
11. Remove cover and lid from outdoor fireplace before lighting.
11
Figure 1
serious,
LP Gas Valve
with Orifice
Figure 2
instructions could
1-800-643-0067
for
Figure 3
Figure 4
Figure 5
Figure 6
OFF" position (Figure 3).
LP Gas
Connection
).
Figure 7
15.7 in-26.7in
40-68cm
Publicidad
