Publicidad
Idiomas disponibles
Idiomas disponibles
CAUTION: Lines coasts after turn off.
Do not use under wet conditions.
CAUTION: Inspect area to be trimmed and remove any wire, cord,
or string-like objects which could become entangled in the rotating
line or spool. Be particularly careful to avoid any wire which might be
bent outwardly into the path of the tool, such as barbs at the base of
a chain link fence.
LINE FEEDING
Your trimmer uses .065" (1.65mm) diameter nylon line to cut grass
and weeds quickly and easily. In time, the tip of the nylon line will
become worn and the auto feed mechanism will automatically feed
and trim a fresh length of line. The cutting line will wear faster if the
cutting is done along sidewalks or other abrasive surfaces or
heavier weeds are being cut. The line will extend approximately ¼
in. with each stop and start of the switch trigger until the line
reaches the length of the grass deflector blade. Do not bump unit
on ground in attempt to feed line or for any other purpose.
Proper Cutting Stance
Weight should be balanced with both feet on solid ground.
Basic Cutting Procedure
Slowly swing trimmer side-to-side as
shown.
EDGING
To convert for maintenance edging, turn off the tool. Holding the
trimmer with one hand, push in the button on the trimmer head and
turn it counter-clockwise. The tool is locked in the edger position.
Return to trimming position by turning the tool off, push in the
button and rotate the trimmer head clockwise until it stops. When
using the tool in the trimmer mode you may choose to fold the wire
edge guide up out of the way.
WARNING: Do not trim near electrical wires or buildings.
OPERATING
CUTTING INSTRUCTIONS
WARNING: Do not allow familiarity with this type of product to
make you careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
Do not operate a string trimmer in a tree, on a ladder, or on a
scaffold; this is extremely dangerous.
Wear non-slip gloves for maximum grip and protection.
REPLACING SPOOL / CLEARING JAMS AND TANGLED
LINES
From time to time, especially when cutting thick or stocky weeds,
the line feeding hub may become clogged with sap or other
material and the line will become jammed as a result. To clear
the jam, follow these steps.
- Turn off the trimmer and remove the battery.
- Press the release tabs on the line spool cover and remove the
cover by pulling it straight off.
- Lift the spool of nylon line out of the hub and clear any broken
line or cutting debris from the spool area.
- In case of jams and tangled line, unwrap about one foot (30cm)
of line to ensure that it is undamaged. If it is OK, rewind it and
insert the line end through the eyelet in the spool hub. Pull the
line through the hole to maintain tension while placing the spool
down in to the hub with the notched side exposed.
- Press the spool down GENTLY and rotate it until you feel it
drop into place.
(When in place, the spool will turn a few degrees left and right
freely.)
- Snap the spool cover back on, insert the battery and turn the
tool on. In a few seconds or less you'll hear the line being cut
automatically to the proper length.
REWINDING SPOOL FROM BULK LINE
(USE ONLY .065" DIAMETER LINE)
Bulk line for your trimmer/edger is available at extra cost from your
local dealer or service center. To install, follow steps:
- Turn off the trimmer and remove
the battery.
- Press the release tabs on the line spool
cover as shown in Fig. 1, and remove the
cover by pulling it straight off. Remove the
spool from the tool and remove and
discard all line on the spool.
- Insert one end of the bulk line into the hole in the spool
as shown in Fig. 2.
- Hold the line in the hole and pull the rest of the line through the
slot in the spool as shown in Fig. 3.
- Snugly and evenly wind the bulk line onto the spool in the
direction of the arrow until it is nearly full.
- Insert the line end through the eyelet in the spool hub as shown
in Fig. 4. Pull the line through the hole to maintain tension while
placing the spool down into the hub with the notched side
exposed.
- Press the spool down GENTLY and rotate it until you feel it
drop into place.
(When in place, the spool will turn a few degrees left and right
freely.)
- Snap the spool cover back on, insert the battery and turn the
tool on. In a few seconds or less you'll hear the nylon line being
cut automatically to the proper length.
4
Publicidad
