Publicidad
Idiomas disponibles
Idiomas disponibles
chain tension properly before use as described in
the Adjusting Chain Tension section.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this product could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com
Saw Chain Sharpening (Fig. N–P)
CAUTION: Sharp chain. Always wear protective gloves
when handling the chain. The chain is sharp and can
cut you when it is not running.
WARNING: Sharp moving chain. To prevent accidental
operation, ensure that battery is removed from the tool
before performing the following operations. Failure to
do this could result in serious personal injury.
WARNING: Do not over file chain rakers, this will
increase the risk of kickback. If the chain has been
sharpened more than four times, replace it.
Each time the chain is sharpened, it loses some of the low
kickback qualities and extra caution should be used.
It is recommended that a saw chain be sharpened no more
than four times.
nOTE: The cutters will dull immediately if they touch the
ground/dirt or a nail while cutting.
To get the best possible performance from your pruner it is
important to keep the teeth of the saw chain sharp. Follow
these helpful tips for proper saw chain sharpening:
1. For best results use a 11/64" (4.5mm) file and a file holder
or filing guide to sharpen your saw chain. This will ensure
you always get the correct sharpening angles.
2. Place the file holder flat on the top plate and depth
gauge of the cutter.
3. Keep the correct top plate
your file guide parallel with your chain (file at 60 ° from
chain viewed from the side) as shown in Fig. N.
4. Sharpen cutters on one side of the chain first. File from
the inside of each cutter to the outside. Then turn your
saw around and repeat the processes (2, 3, 4) for cutters
on the other side of the chain.
nOTE: Use a flat file to file the tops of the rakers (portion
of chain link in front of the cutter) so they are about .025"
(.635 mm) below the tips of the cutters as shown in Fig. O.
5. Keep all cutter lengths equal as shown in Fig. P.
6. If damage is present on the chrome surface of the
top plates or side plates, file back until such damage
is removed.
CAUTION: After filing, the cutter will be sharp, use
extra caution during this process.
WALT recommended
e
WALT call 1‑800‑4‑D
WALT
e
e
23
filing angle line of 30 ° on
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
Three Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/Legal/
Warranty/3‑Year‑Limited‑Warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
English
WALT factory
e
WALT authorized service center.
e
WALT
e
WALT
e
15
Publicidad
