Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
O W N E R ' S M A N U A L
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 16 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, 3/8 Wrench, and Two 7/16 Wrenches (adjustable
wrenches may be substituted for the wrenches).
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use
caution because you could overtighten the hardware and strip the screws.
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer
has to be contacted for replacement parts.
Please Do Not Return This Product To The Store!
Contact Escalade
Phone:
1-866-873-3528
Fax:
1-866-873-3533
E-mail:
tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our Website at:
ON-LINE TROUBLE SHOOTING
ON-LINE PARTS REQUESTS
ADDITIONAL ESCALADE
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
®
Sports customer service department at:
www.escaladesports.com
®
SPORTS PRODUCT INFORMATION
Toll – Free !
Toll – Free !
TECHNICAL ASSISTANCE
FREQUENTLY ASKED QUESTIONS
TABLE TENNIS TABLE
MODEL NOS.
T8620
2L-7631-00
2017 Escalade Sports
Publicidad
Manuales relacionados para Escalade Sports T8620
Resumen de contenidos para Escalade Sports T8620
- Página 1 Escalade® Sports products may be manufactured and/or licensed under the following patents. 6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2017 Escalade Sports...
- Página 2 A. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could overtighten the hardware and strip the screws. B. Indentation mounting guides are small so look closely when attaching hardware. ASSEMBLY TIP C.
- Página 3 Hardware Needed End Rail Mounting CAUTION: Indentations WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS (#3) BE TURNED #8 x 7/16 AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY, YOU WILL DO IRREPARABLE Sheet Metal Screw DAMAGE TO YOUR TABLE WHEN YOU ATTEMPT TO OPEN IT TO THE PLAYING POSITION. (Qty.
- Página 4 Hardware Needed #8 x 7/16 Sheet Metal Screw (Qty. 20) 4. Align the holes in the Mounting Brackets #33 & #34 with Indentations in table top assembly and secure with screws #20 as shown. All holes in each Mounting Bracket must align with Indentations in the top.
- Página 5 Hardware Needed #10-24 X 1/2 Phillips Locknut (Qty. 2) 1/4” Locknut Leg Brace #10-24 X 1/2 Phillips (Qty. 2) Pan Head Screw (Qty. 2) 1/4-20 x 2 1/4 Hex Head Bolt Plastic Washer (Qty. 2) (Qty. 4) 5. Attach Legs (#2) to Mounting Bracket (#34) with Hex Bolt (#38), two Plastic Washers (#24) and Locknut (#15).
- Página 6 Note: To aid in assembly use a cordless drill and Phillips bit, but be Hardware Needed careful to not strip the screws. Wear safety glasses for Step 7. #8-32 X 1 1/4 Phillips Head Screw Note: Rotate U-Support #7 until you see the screw hole in the (Qty.
- Página 7 Hardware Needed #8 x 1 7/16 Sheet Metal Screw (Qty. 6) #8 x 7/16 Note: Rails attach Sheet Metal Screw (Qty. 18) with #20 screws Note: Stiga logo must be on this end of Rail. 8. Lay out Right Side Rails #25, Left Side Rails Detail F #29 and End Rails #26, around edges of table top as shown in Figure 6.
- Página 8 3/4” Spacer Plastic Washer 1/4-20 x 2 1/2 Hex Head Bolt (Qty. 2) (Qty. 2) 1/4” Locknut (Qty. 1) (Qty. 3) 5/16” Spacer 1/4-20 x3 1/4 Hex Head Bolt (Qty. 2) (Qty. 2) 1/4-20 x 1 1/2 Bolt (Qty. 1) 12.
- Página 9 Hardware Needed CAUTION: AT LEAST TWO ADULTS ARE NEEDED 1/4-20 x 1 1/2” Bolt TO MOVE TABLE HALF! (Qty. 2) ¼” Locknut (Qty. 8) 1/4-20 x 2” Bolt (Qty. 2) 1/4-20 x 1-1/4” Bolt Plastic Washer (Qty. 2) (Qty. 4) 17.
- Página 10 Hardware Needed CAUTION: AT LEAST TWO ADULTS ARE NEEDED TO MOVE TABLE HALF! 1/4” Locknut Plastic Washer (Qty. 2) (Qty. 2) 1/4-20 x 2” Bolt (Qty. 2) NOTE: Tighten locknuts #15 finger tight 21. Repeat steps from 1-16 on second half. only.
- Página 11 Hardware Needed 1/4” Locknut (Qty. 2) 1/4-20 x 1 1/2 Bolt (Qty. 2) Figure 3 Figure 9 Figure 3 23. Make sure the legs on the first table top half (the half with the name panel #5) are open. With Assembled in previous step one person on each side of the table, lift and set table half on its legs.
- Página 12 Figure 10 Figure 3 Figure 3 Detail J Hardware Needed #10-24 Lock Nut (Qty. 2) #10 Flat Washer (Qty. 2) #10-24 X 3/4 Round Head Screw (Qty. 2) Detail K INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE OF CAUTION: TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!
- Página 13 28. Secure net posts to center of table by turning the screw on net posts as shown in picture A. 29. Slide Paddle Holder onto net post as shown in picture B. 30. Insert “Slide Lock” into Paddle Holder channel. See Picture C. Repeat Steps 28-30 for other net post.
- Página 14 OPENING AND CLOSING INSTRUCTIONS READ OPERATING INSTRUCTIONS CAREFULLY BEFORE OPERATING TABLE! DO NOT ALLOW CHILDREN TO OPEN TABLE! DO NOT CLIMB, STAND OR JUMP ON TABLE! SERIOUS OR FATAL INJURY MAY RESULT! THIS IS NOT A TOY! TABLE IS CAUTION: TO BE OPENED OR CLOSED BY ADULTS ONLY! FAILURE TO COMPLY WITH OPENING AND CLOSING INSTRUCTIONS COULD RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.
- Página 15 WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship when used for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE...
- Página 16 CARE AND MAINTENANCE You have purchased a quality product that will give you years of enjoyment. By following these simple maintenance steps, you will add to the life of your new table. THE TABLE TOP The top (playing surface) of your table is made of particle board. Like all products made of wood, it can be affected by atmospheric changes in both temperature and humidity.
- Página 17 PRODUCT PARTS LIST - T8620 Key # Description Qty. Part# 4A-5522-01 Table Top 1A-4131-01 Leg & Brace Assembly 2S-6879-10 1” U-Clip 8S-6758-06 Linkage 2S-6422-36 Name Panel 2S-6428-06 Safety Strap 8S-6606-06 U-Support Safety Latch 2S-6264-03 1/4-20 x 1 1/2 Hex Head Bolt WB-1094-00 #10-24 x ¾...
- Página 18 *PARTS LIST ON PREVIOUS PAGE. 2L-7631-00...
- Página 19 Escalade® Sports products may be manufactured and/or licensed under the following patents. 6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563 Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2017 Escalade Sports...
- Página 20 A. Un destornillador eléctrico, puede resultarle muy útil para armar la mesa. Sin embargo, debe usarlo en potencia baja y tener mucho cuidado de no ajustar en exceso y dañar la mesa con los tornillos. B. Los orificios de guía son muy pequeños, ponga atención cuando instalale las partes. CONSEJOS BREVES C.
- Página 21 Necesita: Orificios de guía para el riel ADVERTENCIA: CUANDO ENSAMBLE LA MESA, ES EXTREMADAMENTE IMPORTANTE QUE LAS ABRAZADERAS “U” (#3) ESTÉN PUESTAS COMO ESTÁN MOSTRADAS. SI LfAS ABRAZADERAS “U” ESTÁN COLOCADAS INCORRECTAMENTE, USTED LE OCASIONARA DAÑOS IRREPARABLES A SU #8 x 7/16 MESA CUANDO TRATE DE ABRIRLA EN LA POSICIÓN DE JUEGO.
- Página 22 Necesita: #8 x 7/16 Tornillo para madera (Cant. 20) 4. Alinie los orificios de los soportes de montaje #33 y #34 con los orificios de guía en el tablero e inserte los tornillos #20 como se muestra. Todos los orificios en los Soportes #33 y #34 deben de alinearse con los orificios en el NOTA: Los orificios de guía son tablero.
- Página 23 Necesita: #10-24 X 1/2 Tuerca (Cant. 2) 1/4” Tuerca Abrazadera #10-24 X 1/2 Tornillo (Cant. 2) Phillips (Cant. 2) 1/4-20 x 2 1/4 Tornillo Rondana de (Cant. 2) Plastico (Cant. 4) Instale las patas (#2) al Soporte de Montaje (#34) con el Tornillo de Cabeza Hexagonal (#38), dos Rondanas de Plástico (#24) y la Tuerca de Seguridad (#15).
- Página 24 Necesita: Nota: Use anteojos de seguridad para el Paso 7. #8-32 X 1 1/4 Nota: Rote el soporte en forma de U #7 hasta que se vean los Tornillo Phillips (Cant. 2) orificios a través de las ranuras de las abrazaderas en U #3 donde van los tornillos.
- Página 25 Necesita: #8 x 1 7/16 Tornillo para madera (Cant. 6) #8 x 7/16 Nota: Rieles se Tornillo para madera Nota: El Logo instalan con tornillos (Cant. 18) de “Stiga” debe #20. de estar en este extremo del riel. Debajo de la mesa 8.
- Página 26 Separador 1/4-20 x 2 1/2 Tornillo Rondana de de 3/4” 1/4” Tuerca Plástico (Cant. 1) (Cant. 2) (Cant. 3) (Cant. 2) Separador de 5/16” 1/4-20 x3 1/4 Tornillo (Cant. 2) (Cant. 2) 1/4-20 x 1 1/2 Tornillo Una los extremos de los Tubos Conectores #4 con los dos orificios hacia (Cant.
- Página 27 Necesita: ADVERTENCIA: 1/4-20 x 1 1/2” Tornillo ¡POR LO MENOS SE REQUIERE DE DOS (2) (Cant. 2) ADULTOS PARA MOVER LA MITAD DE LA MESA! 1/4” Tuerca (Cant. 4) 1/4-20 x 2” Tornillo (Cant. 2) 1/4-20 x 1-1/4” Tornillo Rondana de Plástico (Cant.
- Página 28 Necesita: ADVERTENCIA: ¡POR LO MENOS SE REQUIERE DE DOS (2) ADULTOS PARA MOVER LA MITAD DE LA MESA! Rondana de 1/4” Tuerca Plástico (Cant. 2) (Cant. 2) 1/4-20 x 2” Tornillo (Cant. 2) NOTA: Apriete las tuercas de seguridad #15 únicamente con la mano.
- Página 29 Necesita: Recargue esta mitad contra la pared. La Primera Mitad de la mesa que ensamblo. La Segunda Mitad de la mesa que ensamblo. 1/4” Tuerca (Cant. 2) 1/4-20 x 1 1/2 Tornillo (Cant. 2) Figura 3 Figura 9 Figura 3 23.
- Página 30 Figura 10 Detalle J NO SOBRE AJUSTE EL PASADOR DE SEGURIDAD #8. Necesita: DEBE DE GIRAR LIBREMENTE! #10-24 Tuerca Vista de (Cant. 2) Arriba #10 Rondana (Cant. 2) Placa #5 #10-24 X 3/4 Tornillo Phillips Pasador de Seguridad #8 (el borde se extiende sobre la placa) (Cant.
- Página 31 28. Asegure los postes de la red al centro de la mesa, ajuste los tornillos en los postes de la red, como se muestra en la Dibujo A. 29. Inserte el sostenedor de la paleta de ping pong en el poste de la red, como se muestra en el dibujo B.
- Página 32 INSTRUCIONES PARA ABRIR Y CERRAR LA MESA ¡LEA AS INSTRUCCIONES DE MANEJO ANTES DE MOVER LA MESA! ¡NO PERMITA QUE NIÑOS ABRAN LA MESA! NO DEBEN DE PARARSE, SUBIRSE O BRINCAR SOBRE LA MESA. PUEDEN OCURRIR LESIONES GRAVES O ADVERTENCIA! MORTALES.
- Página 33 GARANTÍA LIMITADA POR 90 DÍAS ® Esta garantía es aplicable para consumidores de la compra original de cualquier producto ESCALADE SPORTS (en adelante denominado el "Producto"). DURACIÓN DE LA GARANTÍA: Se garantiza este Producto al comprador original por un período de (90) días a partir de la fecha de compra.
- Página 34 CUIDADO Y MANTENIMIENTO Usted ha comprado un producto de calidad que podrá disfrutar muchos años. Si sigue estos simples pasos de mantenimiento, alargará la vida de la mesa. TABLERO El tablero (superficie de juego) está construido de aglomerado. Al igual que todos los productos de madera, se puede ver afectado por cambios de temperatura y humedad causando una leve deformación por expansión o contracción.
- Página 35 Lista de partes reemplazables - T8620 Descripción Cant. Modelo No. de ref 4A-5522-01 Tablero 1A-4131-01 Pata 2S-6879-10 Abrazadera en U -1” 8S-6758-06 Tubo Conector 2S-6422-36 Placa con logotipo 2S-6428-06 Tira de metal de Seguridad 8S-6606-06 Tubo de Soporte en U...
- Página 36 *LISTA DE PARTES EN LA PAGINA ANTERIOR. 2L-7631-00...