Publicidad
IMPORTANT
You
must build the Palermo Gazebo before you attached the Ledro walls.
Before
beginning
please refer
to the Assembly Manual
in
the Palermo Gazebo carton.
Please
read these
instructions carefully before you start to assemble this product.
Please
carry out the
steps in
the order
set
out
in
these
instructions.
Keep
these
instructions
in
a
safe
place
for future
reference.
Safety advice
For
safety purposes we
strongly recommend the product to
be
assembled by at least
two
people.
Some parts may have sharp edges.
Please be
careful when handling components. Always wear
gloves,
eye
protection,
and long
sleeves
when assembling or performing any maintenance
on
your product.
Do
not
attempt
to assemble the product
in
windy or wet conditions.
Do
not
attempt
to assemble the product if you
are
tired,
have
taken drugs,
medications or alcohol, or if you
are
prone to dizzy
spells.
Dispose
of
all
plastic
bags safely
-
keep
them
away
from children's
reach.
Keep
children
away
from the assembly
area.
When using
a
stepladder or power tools, make
sure
that
you
are
following
the manufacturer's
safety advice.
Do
not climb or stand on the
roof.
Do
not hang or
lay
on the profiles.
Heavy articles should not
be
leaned against the poles.
Keep
roof
and
gutters
clear
of
snow,
dirt
& leaves.
Heavy snow load on
the roof
can make
it unsafe to stand below or nearby.
If
color
was
scratched
during
assembly it
can be
fixed.
Cleaning
instructions
In
order to
clean
the product,
use
a
mild detergent solution and
rinse
with
cold clean water.
Do
not
use
acetone, abrasive cleaners, or
other
special
detergents to
clean
the
panels.
Clean
the product once assembly
is
complete.
Before
starting
assembly
Choose
your
site
carefully before beginning
assembly.
The
ground
surface must
be
perfectly flat
and leveled and
have
a
solid
base such
as
concrete,
asphalt, deck
etc.
Sort the parts and check against the
content
parts
list.
Parts
should
be
laid
out
close at hand. Keep
all
small parts (screws etc.) in
a
bowl
so
they do
not get
lost.
Please
consult your
local
authorities if
any
permits
are
required prior to constructing the product.
During Assembly
UI
When
encountering the information
icon, please refer to the relevant
assembly step for additional comments and
assistance.
an.
This
icon indicates
that the installer should
be
inside the product.
Attention
This
icon indicates
that
the installer should
be
II
outside the product.
During assembly
use
a
soft surface below the parts to avoid scratches and
damages.
Please
make
sure
you install the panels
with the
UV
protected
side
out (marked with
"THIS
SIDE
OUT")
and remove the sticker
as
panels
are in place.
Step
1: Please
assemble the gazebo
as
per
its
instructions.
Do
not
assemble the plastic
corner
pieces
(part
#8327), the plastic clips
(part
#7829)
and do
not anchor to the
base
you prepared
in
advance!
Step
2:
Dismentle the internal foot-pads
(part
#212
or
8758).
Step
5:
During assembly, from this step onwards,
use
a
carton or other soft material below
the
parts to avoid scratches and damages.
Step 8:
Peel
the film from the panels'edges before sliding them into the profiles,
peel
the
entire film once the assembly
is
complete.
Step 15: Note
-
done from inside the gazebo.
Step 26: Apply silicone
on
the inside
in
order to
seal
as
shown
in
drawing
a.
Screws
and
corner cover
are
supplied with the gazebo!
Step 27: Make sure the gazebo
is
leveled
prior to anchoring the corner
poles,
use
suitabled
screws
and plugs
as
per
your
chosen
base.
Step 29: Make sure the entire gazebo
is
leveled prior to anchoring it to the surface
of your
choosing.
Use
suitable
screws
and plugs.
Step 30: Install the sealing strip on the
outer
side
as
shown
in
the diagram.
Use
mild
soap
if
needed.
Tighten
all
screws at
the end of assembly.
Do
not tighten
screws
and nuts (8192
&
466)
until completion of assembly
process.
These
2
icons
indicate if screws'tightening
is
required or not.
Note:
Anchoring this product to the ground
is
essential to
its
stability
and rigidity.
It
is
required to complete this
stage
in
order for your warranty to
be
valid.
Publicidad
