Publicidad
Idiomas disponibles
Idiomas disponibles
O P E R AT I O N
Stop Watch
(continued)
2. To start the timer, push the CHANNEL SELECT
button up. To stop the timer, push the CHANNEL
SELECT button up again.
CHANNEL
3. To restart the timer from
SELECT
that point, push the
button
CHANNEL SELECT button
up a third time. Or to
reset the timer back to 00 :oo:oo , press the
ENTER button.
4. After starting the timer, you can view an
interim "split" time (while the timer continues
to run) by pushing the CHANNEL SELECT
button down. To return to the timer, push
the CHANNEL SELECT button down again.
5. Press and release the MODE button to leave
Stop Watch mode.
MODE
While in Stop Watch mode,
button
your microTALK
®
will alert
you to incoming calls, but
the LCD will continue to
show the Stop Watch display. You can also
transmit as normal with the CALL button, TALK
button or in VOX mode; when you do, the LCD
will automatically return to normal display. The
timer will continue to run and can be viewed
simply by returning to Stop Watch mode.
(NOTE: You can not view the compass
mode while in Stop Watch mode.)
13
ENGLISH
Clock
You can set your microTALK
®
to display the
time of day. To use the Clock function:
Press the MODE button
MODE
ENTER
button
button
until the current time
is displayed in the LCD.
To set the time of day:
1. While in Clock
mode, press and
release the ENTER
button. The hour
will begin flashing
in the LCD.
2. Push the CHANNEL
SELECT button
up or down to
set the hour.
3. Press and release the ENTER button again.
The minutes will begin flashing in the LCD.
4. Push the CHANNEL SELECT button up or
down to set the minutes.
5. Press and release the ENTER button again.
"AM" or "PM" will begin flashing in the
LCD. Push the CHANNEL SELECT button
up or down to set AM or PM.
ENGLISH
6. Press and release the ENTER button to set the
time and return to Clock mode. Press and
release the MODE button to leave Clock mode.
While in Clock mode, your microTALK
will
®
alert you to incoming calls, but the LCD will
continue to show the Clock display. You can
also transmit as normal with the CALL button,
TALK button or in VOX mode. When you do,
the LCD will automatically return to normal
display. Once you have finished transmitting,
the unit will automatically return to Clock mode.
(NOTE: You can not view the compass mode
while in Clock mode.)
Compass
Your microTALK features an 8-point digital
compass. (NOTE: Because the surrounding
terrain can affect compass accuracy, it is
recommended that you calibrate the compass
before each use.) It is important to keep the
radio parallel to the ground at all times while
calibrating and using the compass.
Calibrating the Compass
1. Press and hold the COMPASS button for
2 seconds. "Compass" and "CALIbr" will
appear in the LCD.
COMPASS
button
O P E R AT I O N
2. Hold the radio in front of you, parallel to
the ground, and turn around in a circle at
least two times, then press Compass button
again. Or you may also place the radio on
the palm of one of
your hands, parallel
to the ground, and
turn it in a circle at
least two times with your other hand, then
press the COMPASS button again.
3. If compass calibration was successful,
"SUCCES" will appear in the LCD for
1-second, then the unit will automatically
return to compass mode.
4. If "FAIL" appears in the LCD, repeat steps
1 and 2. (If you receive repeated "FAIL"
messages, change locations and repeat
steps 1 and 2.)
Using the Compass
After proper calibration
(see steps 1-4), press
parallel to ground
and release the
COMPASS button.
"Compass" and the
current direction will be
displayed. The radio
must always be parallel to the ground to give
accurate directional readings. The direction of
the antenna is the direction displayed in the LCD.
To exit Compass mode, press and release the
COMPASS button again.
14
Publicidad
