Kärcher T-Racer Surface Cleaner Manual Del Usuario página 6

Symbols on the device
DANGER
Risk of injury! Never reach under the
edge of the T-Racer during operation
HARD For durable surfaces, e.g. tiles, concrete,
stone
SOFT For sensitive surfaces, e.g. wood
Device description
For the illustrations, refer to the graphics page
Illustration A
Extension tube
1
Rotor arm height adjustment
2
Casing
3
Bayonet connector with union nut
4
Handle
5
High-pressure nozzle
6
Rotor arm
7
Extension tube installation
Note
Ensure that the device components are tightly connect-
ed on installation.
Illustration B
1. Plug the bayonet into the mounting.
2. Turn the extension until it latches into place.
3. Tighten the union nut.
Repeat the procedure for all further extension tubes.
Initial startup
Selection of the high-pressure nozzles
Using the appropriate high-pressure nozzles is a pre-
requisite for fault-free operation.
Note
These are to be selected according to the flow rate (l/
min). Information on the flow rate is provided in the op-
erating instructions or on the type plate of the high-pres-
sure cleaner.
Note
The yellow high-pressure nozzles are already fitted.
Flow rate l/min (l/h) High pres-
sure class
(e.g.)
Less than 5.8 (348) K2 - K3
5.8 (348) - 7.5 (450) K3 - K5
Greater than 7.5 (450) K6 - K7
Operation
Note
The extension tubes can be used with all Kärcher ac-
cessories.
Note
For optimum cleaning results, do not operate the high-
pressure cleaner in the Eco mode.
6
Remove coarse dirt from the surface to be cleaned (e.g.
by sweeping) before using the device to avoid damage
to the T-Racer.
ATTENTION
Damage to the rotor arm
The rotor arm can be damaged if it hits edges and cor-
ners.
Do not move the device over free-standing corners and
edges.
Illustration C
Note
● The T-Racer is not suitable for scraping or scrub-
● Test the device on an inconspicuous area before us-
● Do not allow it to remain in one area, but keep it in
1. Attach the T-Racer to the high-pressure gun using
2. Adjust the rotor arm height adjustment. according to
3. Unlock the lever of the trigger gun.
4. Pull the lever of the trigger gun.
5. Clean the floor surface by guiding the T-Racer over
1. Attach the T-Racer directly to the high-pressure gun.
2. Clean the wall surface.
The clearance of the high-pressure nozzles to the sur-
face to be cleaned can be adjusted via the rotor arm
height adjustment.
Adjust the rotor arm height adjustment. according to the
surface to be cleaned.
Colour of the
Illustration D
high-pressure
For powerful cleaning of stubborn soiling on dura-
nozzles
ble surfaces, e.g. tiles, concrete, stone:
1. Set the rotor arm height adjustment to "HARD".
Green
For cleaning sensitive surfaces:
Grey
2. Set the rotor arm height adjustment to "SOFT".
Yellow
Rinse off the device with a gentle water stream after use.
 Detach the T-Racer and any extension tubes from
 Rinse off the T-Racer with the high-pressure gun (with-
Store the device in a frost-protected place.
English
Cleaning floors
bing.
ing on sensitive surfaces, e.g. wood.
motion.
the extension tube.
Illustration B
a Press the extension tube onto the bayonet con-
nector of the high-pressure gun.
b Turn the extension tube by 90° until it latches into
place.
c If necessary, repeat the procedure for further
connections.
the surface to be cleaned.
The device switches on.
the floor surface without exerting excessive pres-
sure.
Cleaning wall surfaces
a Press the bayonet connector of the T-Racer into
the connection on the high-pressure gun and
then turn by 90° until it latches into place.
b Tighten the union nut if present.
Rotor arm height adjustment
After use
the high-pressure gun.
out accessories) or wipe down with a damp cloth.
Storage