Publicidad
Idiomas disponibles
Idiomas disponibles
Fig. N
7. Lift the rear of driver until at an angle and pull the driver
out. Refer to Figure O.
8. Replace driver and follow steps in reverse to reassemble
9. Ensure new driver slides smoothly through the gun
before full reassembly.
Fig. O
10. Return the driver, guide rods, bumpers, housing end
cap, and removable top stand back onto the unit. It
is important to try the alignment of the driver and
the flywheel before screwing the housing end cap
back on to the unit. This can be done by connecting
a battery and pushing then releasing the nose of the
unit against a bench or hard surface. This will start the
motor spinning.
nOTE: When the driver and the flywheel are correctly
aligned, you will hear the motor coast back down
from full speed. If the driver and the flywheel are not
correctly aligned, the motor may not start up, may
slow down much faster than normal along with a loud
grinding noise from the unit. If this happens remove
and reseat the driver, making sure the bumpers are
seated correctly.
WARNING: Always test the unit by firing 3/4" pins
in power setting 1 into scrap material, to ensure that
the tool is working properly. If tool does not operate
properly, contact a recognized D
center immediately.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
East Joppa Road, Towson, MD 21286, call 1–800–4-D
(1–800–433–9258) or visit our website www.D
22
21
20
WALT service
e
WALT Industrial Tool Co., 701
e
WALT.com.
e
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a D
or a D
e
identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
WARRAnTY sERViCE: Registering your product will
•
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of
•
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
•
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.dewalt.com or call 1-800-4-D
433-9258). This warranty does not apply to accessories
or damage caused where repairs have been made
or attempted by others. THIS LIMITED WARRANTY IS
GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
damages, so these limitations may not apply to you. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
by our:
D
WALT will maintain the tool and replace worn parts
e
caused by normal use, for free, any time during the first year
after purchase. ADD WEAR STATEMENT: NO SPRINGS
2 YEARs FREE sERViCE On DEWAlT BATTERY PACKs
DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,
DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361
WALT
e
WALT factory service center
e
WALT authorized service center. Always use
e
WALT tools are covered
e
1 YEAR FREE sERViCE
English
WALT (1-800-
15
Publicidad
