Alto Professional ZMX122FX Manual De Inicio Rápido página 4

23. EFFECTS SELECTOR: Selects the effect that the mixer's internal effects processor will apply to the various channels.
Each channel can send different levels of audio to the processor by adjusting their FX POST SEND knobs. See the
EFFECTS section for an explanation of the available effects.
24. VARIATIONS SELECTOR: Selects the amount of the effect applied to the various channels.
25. FX MUTE: Press this button to mute/unmute the effects.
26. AUX RETURN TO MAIN MIX: Adjusts the volume of the signal being sent into the AUX RETURN INPUTS and routed to
the MAIN MIX OUTPUTS.
27. AUX RETURN TO AUX 1 MON: Adjusts the volume of the signal being sent into the AUX RETURN INPUTS and routed
to the CTRL ROOM OUTPUTS.
28. 2-TRACK LEVEL: Adjusts the input signal level of the 2-TRACK INPUTS.
29. CTRL ROOM / PHONES: Adjusts the volume of the CTRL ROOM OUTPUTS and your headphones.
30. MAIN / 2-TRACK: Press this button to select which signal is routed to the CTRL ROOM OUTPUTS and your
headphones: the main mix or the signal from the 2-TRACK INPUTS.
31. 2-TRACK TO MAIN: Press this button to select which signal is routed to the MAIN MIX OUTPUTS: the main mix or the
signal from the 2-TRACK INPUTS.
32. MAIN VOLUME: Adjusts the volume of the MAIN OUT.
33. LED METERS: Shows the audio level of the main mix. Turn the volume down if the CLIP LED lights up excessively.
34. PHANTOM POWER: This switch activates and deactivates phantom power. When activated, phantom power supplies
+48V to the XLR mic inputs and the LED above the switch will be lit. Please note that most dynamic microphones do
not require phantom power, while most condenser microphones do. Consult your microphone's documentation to find
out whether it needs phantom power.
35. POWER LED: Illuminates when the mixer is on.
Effects
To hear the effects on a channel: Use the EFFECTS SELECTOR to choose one of the effects below, adjust the parameter
with the VARIATIONS SELECTOR, then turn up the FX POST SEND for that channel.
# Preset
1 Vocal 1
2 Vocal 2
3 Large Hall
4 Small Hall
5 Large Room
6 Small Room
7 Plate
8 Tape Reverb
9 Spring Reverb
10 Mono Delay
11 Stereo Delay
12 Flanger
13 Chorus
14 Reverb+Delay
15 Reverb+Flanger
16 Reverb+Chorus
4
Description
Reverb, simulating a room with a small delay time.
Reverb, simulating a small space with a slight decay
time.
Reverb, simulating a large acoustic space.
Reverb, simulating the acoustics of a stage space.
Reverb, simulating a studio with many early reflections.
Reverb, simulating a bright studio room.
Simulates bright plate reverb.
Simulates classic tape delay created by multiple
playback heads.
Simulates the lightly stretched sound of spring reverb
from analog transducers.
Reproduces the signal after a small period of time.
Reproduces the signal after a small period of time with
a slight difference between the two stereo channels.
Classic stereo flanging effect, similar to a jet plane
taking off.
Simulates the full, complex, watery sound of several
instruments playing the same thing.
Delay effect with room reverb.
Stereo flanger effect with room reverb.
Stereo chorus effect with room reverb.
Parameter
Decay time
Pre-delay
Decay time
Pre-delay
Decay time
Pre-delay
Decay time
Pre-delay
Decay time
Pre-delay
Decay time
Pre-delay
Decay time
Pre-delay
Decay time
Pre-delay
Decay time
Pre-delay
Delay period 60~650ms
Delay period 210~400ms
Feedback
Rate 0.16~2.79Hz
Rate
Delay period 211~375ms
Reverse decay time
Flanger rate
0.16~2.52Hz
Reverse decay time
Chorus rate 0.5~4.74Hz
Reverse decay time
Range
0.8~1.1s
0~79ms
0.8~2.5s
0~79ms
3.6~5.4s
23~55ms
1.0~2.9s
20~45ms
2.9~4.5s
23~55ms
0.7~2.1s
20~45ms
0.6~6.1s
10ms
1.3~5.4
0~84ms
1.3~5.4s
0~84ms
37~73%
0.5~5Hz
1.0~2.9s
1.5~2.9s